#51
|
|||
|
|||
Hi!
Thanks for all information, I just installed the EXP to mine MC 250, 2003 and IT seams to work well, i have a small drag when i have a gear in, It's really greate to run whit the autoclutch I put 1,8 mm washer on the outside of the lifter, took some time to get the right hight but now it works well, no slip what i can tell Cheers 😀
__________________
Gasgas 250 MC 2003 |
#52
|
|||
|
|||
Are the guys that are putting in the rekluse exp buying the exp for a 94-07 cr 250? I'm thinking about trying it.
Sent from my iPhone using Tapatalk |
#53
|
|||
|
|||
This is the thread I was looking for will update it when my Rekluse arrives
__________________
05 GG EC 300 Rekluse Smart Carb SSS Front & Ohlins Rear by MPE FMF Gnarley & Powercore 2 2013 (4t) Racing update Kit |
#54
|
|||
|
|||
So simple, CR250 Rekluse Core, then just used 2 extra GG washers on top of the normal 1 and all is sweet, will be giving it a good try out tomorrow
__________________
05 GG EC 300 Rekluse Smart Carb SSS Front & Ohlins Rear by MPE FMF Gnarley & Powercore 2 2013 (4t) Racing update Kit Last edited by BigAl; 03-05-2016 at 03:42 AM. |
#55
|
|||
|
|||
I can't wait to hear. Thanks again. What year cr250 clutch did you buy? (I assume you mean 2 stroke right?)
Sent from my iPhone using Tapatalk |
#56
|
|||
|
|||
Rekluse RMS-6013, Cr250R (92-07), Crf450R (02-08) (14-15). CRF450X (05-09) (14-15)
__________________
05 GG EC 300 Rekluse Smart Carb SSS Front & Ohlins Rear by MPE FMF Gnarley & Powercore 2 2013 (4t) Racing update Kit |
#57
|
|||
|
|||
How is your rekluse working? My friend just installed one in his bike and now he is faster than me in the woods!
Sent from my iPhone using Tapatalk |
#58
|
|||
|
|||
Quote:
Every 1 that has ridden it since it went in loves it as well
__________________
05 GG EC 300 Rekluse Smart Carb SSS Front & Ohlins Rear by MPE FMF Gnarley & Powercore 2 2013 (4t) Racing update Kit |
#59
|
|||
|
|||
Does put a Suzuki thrust washer 2.0mm instead of stock 2.8 mm under clutch hub make sence (clutch hub to basket spacer) when converting to a CR250R cluth plates?
We have hydraulic clutch that push long clutch rod (which push pressure plate), so if overall plates pack size is bigger than standard (34.5mm CR250 vs 33.3mm GG300), then after additional 2-3 pushing clutch lever that long rod will be pushed forward that extra 1mm and stay there forever. So i don't understand how changing thrust washer are changing something? Besides that - basket, plates and pressure plate is one whole assembly, which moving inside (in engine) when changing that washer to thinner one - so really nothing happens to compensate new pack height of CR250 plates. Only 6 springs are more preloaded (~1mm), but i see you never feel that after conversion. Does the way of my thoughts right? |
#60
|
||||
|
||||
Don't spose someone could point me in the direction of the thread that talked about clutch burnishing(to eliminate drag apparently) could they please? Searched but can't find. Cheers
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
TXT 200 pro clutch.. | jhendr3702 | Other GasGas Bikes/Quads | 1 | 01-28-2011 10:10 AM |
Clutch problems | gaser | Enduro Engine - 2 stroke | 5 | 11-15-2010 07:51 AM |
Clutch going out? | Crankin04 | Enduro Engine 4 stroke (including EFI & Exhaust) | 5 | 07-30-2010 01:00 PM |
450 clutch, same as DRZ? | Devondan | Enduro Engine 4 stroke (including EFI & Exhaust) | 2 | 10-01-2009 07:58 PM |
What clutch oil is best? | wence | Enduro Engine - 2 stroke | 5 | 08-20-2009 03:57 AM |