|
Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc. |
|
Thread Tools | Display Modes |
|
#1
|
||||
|
||||
Keihin PWK Needle Chart
A fellow member (jhendr3702) sent this needle chart to me. It provides a nice description of the needle codes for Keihin PWK carbs. I'm creating a "sticky" for future reference.
CLICK ON THE THUMBNAIL BELOW TO ENLARGE:
__________________
Matt Current: 2009 Yamaha FZ1 Previous: 2001 GasGas TXT280, 2001 GasGas XC250, 2004 KTM 200EXC, 2007 GasGas EC250, 2007 Husqvarna SM610, 2008 Husqvarna WB165 |
#2
|
||||
|
||||
Much better than the poor images from elsewhere. Thanks
__________________
2011 Gas Gas EC300 38mm, 2008 Husky TE610, 2003 Beta Rev3 250 |
#3
|
|||
|
|||
Which Needles?
I purchased a used 2003 EC250 and with it is an envolope full of jets and needles. After searching the web I have not found any clear information regarding the needles I now posses. They are as follows: N1EC, N1EG, N1EE, and NBHK. Can anyone help me as to what needles these are? Thanks
|
#4
|
||||
|
||||
Quote:
the jet needles that GasGas put in the Keihin carbs were the "N1E" series. The N1EC, N1ED, N1EE, and N1EF (progressively leaner as you go down the alphabet) were what came in the older models. Around 2005, we started seeing the N1EG jet needles. In this series, I prefer the N1EG. When we started using that needle, we were finally able to get our bikes to idle without bottoming out the throttle stop screw. In my 2006 DE300, I ran it with the "Jesus clip" in the second groove from the top. (along with a 42 pilot and a 175 or 178 main, according to the temps outside). I don't have a chart, so I'm not sure of the NBHK. Matt, Thanks again for posting the chart. It sure has come in handy. Good Riding! Jim .
__________________
Jim Cook Smackover Racing Team LAGNAF '11 Gas Gas EC250 (primary ride) '06 Gas Gas DE300 2004 Gas Gas TXT300 Pro '94 Husaberg FE350 '86 Yamaha IT200 '86 Honda TRL200 Reflex '04 KTM 525EXC (soon to be dual sported) Several others, including project bikes, Deb's bike, and a fleet of grandkids' bikes Let's go riding! http://www.jebruns.com/Wudi19/wudi19.html http://www.ahrma.org/schedules-results/cross-country/ |
#5
|
|||
|
|||
Gas gas ec 300 2009
Hey I noticed this post and was hoping you could help me I have a gas gas ec300 09 I am trying to get It to run a bit ritcher and have limited knowledge on how to jet my carb it is a kehnin pwk 38 mm the previous owner told me he had changed the needle on inspection I found a needle stamped chn I also got the other needle which is a n1ef I contacted gas gas and they told me the stock needle is a n1eg I am lost as to what to do next I haven't checked my main jet yet I thought I could just lift my needle 1 clip position but it was already at the top I only suspect it is running lean because my exhaust has no oily residue at all and has a slightly brown tinge not grey the spark plug dosent look to bad just chacole black I would apriceate any advice
|
#6
|
||||
|
||||
list what elevation range u ride,your avg temp range,what fuel octane/oil ratio u use,clip position and what jets u have now,(slide # if able) and someone will have a good starting suggestion.alternatively trawl thru the jetting database for similar bike operating in similar conditions to get an idea.how does it feel riding it?any starting/idle issues?bogging when you crack open quickly?the n1eg is I think 1 step leaner in diameter than n1ef(assuming your main is stock?)dont know about the chn.when you say the needle is at the top(highest/richest position)you mean the clip is in the lowest slot right?clip in top slot is leanest,lowest needle position.just wondering as the needle in it(n1ef)is richer than stock(n1eg),and would be surprising if it needed the richest clip slot also
__________________
2013 ec200r |
#7
|
|||
|
|||
Keihin PWK Needle Chart
The float level adjustment is what Jakobi is referring too. Look at the top of your carburetor and tell us what it looks like. Also need to determine if it is a 36 or 38 mm. Should be stamped on the carb body somewhere
Sent from my iPhone using Tapatalk |
#8
|
|||
|
|||
Trying to order a NE1G needle for my AS1 carb. Going to the Keihin order sheet and I have no idea what the corresponding code is for that needle....anyone have an idea?
|
#9
|
|||
|
|||
This is what I go to when it comes time for Jetting.
http://www.jetsrus.com/a_jets_by_car...n_N427-48.html And http://www.kyajet.de/ |
#10
|
||||
|
||||
Quote:
I always got my N1EG needles for the AS1 carbs through GasGas parts, but it is a 1998 Kawasaki KX250 series jet needle. Part #16009-1764 (NEEDLE-JET,N1EG) parts diagram reference #16009F 1998 was the last year for which I saw the needle listed. I checked two parts suppliers, Bike Bandit and Rocky Mountain ATV, but neither of them show the jet needle as being available. A Kawasaki dealer may be able to help you. Good luck and good Riding to you! Jim .
__________________
Jim Cook Smackover Racing Team LAGNAF '11 Gas Gas EC250 (primary ride) '06 Gas Gas DE300 2004 Gas Gas TXT300 Pro '94 Husaberg FE350 '86 Yamaha IT200 '86 Honda TRL200 Reflex '04 KTM 525EXC (soon to be dual sported) Several others, including project bikes, Deb's bike, and a fleet of grandkids' bikes Let's go riding! http://www.jebruns.com/Wudi19/wudi19.html http://www.ahrma.org/schedules-results/cross-country/ |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Needle Chart | Brian | Enduro Intake/Carburetion - 2 stroke | 2 | 11-23-2010 02:29 PM |
cdi chart? | stainlesscycle | Enduro Electrical & Wiring | 4 | 04-19-2010 06:57 AM |
Dyno Chart | Grampy | Enduro Engine - 2 stroke | 1 | 12-17-2008 08:56 PM |
KEIHIN float valve | nhrider | Enduro Intake/Carburetion - 2 stroke | 1 | 06-17-2008 01:10 PM |
Keihin Carb | Harry | Enduro Engine - 2 stroke | 4 | 05-30-2007 06:52 AM |