|
|
|||||||
| Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
 |
|
|
Thread Tools | Display Modes |
|
#1
08-16-2009, 07:54 AM
|
||||
|
||||
Clutch line?
Hey Guys ,
Dropped the bike stupidly on the weekend and knocked the barkbuster into the clutchline. While moving the barkbuster back it pulled down on the clutch line and fractured it. Where is the best place to buy an 07 Ec 300 clutch line? From reading the searches I have found that Dot 4 fluid is best, correct? If anyone has one that they are not using or don't need could they let us know? Cheers Mark 
|
|
#2
08-16-2009, 11:52 AM
|
||||
|
||||
|
NO NO NO DOT 4(read the top of the clutch res0
100% mineral oil on the 07 this translates to going to a pharmacy and getting {LOLOLOL} laxative!!!! must be mineral oil only though, so no xlax  and this stuff is 10x slicker than snot, do your best not to get any on anything!
__________________
Le Crutan  98 ec250 sixdays, doma, eline pipe guard, zokes shivers from a cr250,fredette racing chain slider, protaper withbarkbusters (SOLD)  FOR THE SECOND TIME 07 EC300 polisport headlight, acerbis taillight ltr pv cover and case saver,trailtech endurance,120z fww, g2 throttle,xr chain puck:
|
|
#3
08-16-2009, 01:50 PM
|
||||
|
||||
|
Quote:
I had a quick read of some posts yesterday and was going to fix it temporarily and top it up. Lucky I couldn't fix it I guess. Thanks Mountain thumper. Cheers Mark
|
|
#4
08-16-2009, 05:42 PM
|
|||
|
|||
|
Not sure how the line on the 07 mounts to the mc but on my 03 I used a braided steel line from enduro eng. for a KTM exc 200ish.. just had to use a banjo bolt in the mc end which made it fit better with the handguards anyway..
__________________
Steve 16 Beta 350rr 04 KTM 525 sx/exc gone 03 KTM 625 sxc-rehab unit-did its job and now gone 03 GG 250 ec-gone 97 GG 250 ec Gone
|
|
#5
08-17-2009, 02:38 AM
|
|||
|
|||
|
Hi Wence,
I think one of these would work ok http://www.pyramid-parts.com/brake-h...omeaagbpia0vqq I've got one from them for the rear brake, only took about 3-4 days to turn up. The clutch line runs real close to the Bark Busters. I've been toying with the idea of changing to a banjo bolt set up to fix it once & for all.
__________________
--------------------------- GG EC300 2007.
|
|
#6
08-17-2009, 02:42 AM
|
||||
|
||||
|
Quote:
Thanks for all the help, I will follow it up and let you know. Thanks again Mark.
|
|
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Front brake line? | nick790 | Enduro Chassis & Body | 0 | 05-27-2009 03:50 AM |
| looking for on-line shops in the U.S. | splint | General Discussions & Announcements | 2 | 05-20-2008 09:31 PM |
| On line MX game | gasgasjohn | General Discussions & Announcements | 1 | 09-25-2006 02:18 PM |
Linear Mode
