Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Engine - 2 stroke

Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc.


Reply
 
Thread Tools Display Modes
  #11  
Old 05-10-2007, 08:20 AM
iancp5's Avatar
iancp5 iancp5 is offline
Senior Member
 
Join Date: Aug 2006
Location: U.K.
Posts: 829
Default

Think I used Athena but I'd have been happy with Wiseco. Anyone with a name brand. I'd be a little concerned about some Chinese jobby free with my breakfast cereals!


Reply With Quote


  #12  
Old 01-03-2012, 02:43 PM
AMCQ AMCQ is offline
Member
 
Join Date: Oct 2006
Location: West Midlands UK
Posts: 2
Default No marks on my cylinder?

Quote:
Originally Posted by GMP View Post
They are stamped on the rear of the cylinder just above the base. If the cylinder is on the bike it may be hard to see, try an inspection mirror.
Need some help to work out what size my cylinder is. The bike is a 2003 EC200, and it is getting its 1st top end rebuild after sitting unused for 4yrs.

I read the quote that the marking should be on the back of the cyl, but GasGas uk tell me it should be below the exhaust port! But when I look at my cyl, there is no marking stamped in either location!

There is a pen marking on the base gasket face which says 5A or SA, and a small stamp to the side of the exhaust face but it looks like a logo JAP in a oval.




The only clue i can find is top of the piston is marked 62.45mm.


So from that should I assume this is an A piston, as I read somewhere that the sizes are 62.45, 62,46 and 62,46
__________________
Alastair Mc

GG EC200 2003
Reply With Quote
  #13  
Old 01-03-2012, 04:25 PM
Leo's Avatar
Leo Leo is offline
Senior Member
 
Join Date: Sep 2008
Posts: 499
Thumbs down

Be careful with go faster if you is from outside US.
I'm not happy with them since i not received my parts and anyone replied my emails.

Go to Ebay.
__________________
www.endurohp.eng.br
Sherco ST300 2015 (Trials)
https://www.instagram.com/leocm74/
Brasil!
Reply With Quote
  #14  
Old 01-03-2012, 07:36 PM
PEB PEB is offline
Senior Member
 
Join Date: Aug 2006
Posts: 1,152
Default

The size is on the carb side of the cyl. stamped on the flat area. Should be an a,b,c or d. Keep looking it is there.
Reply With Quote
  #15  
Old 01-03-2012, 08:47 PM
Rick's Avatar
Rick Rick is offline
Senior Member
 
Join Date: Aug 2006
Location: Lodi, Ca
Posts: 1,930
Default

Damm, Leo......nothing like throwing Go Fasters under the bus! Not really the place to talk smack!

Yea....Ebay will save the day
__________________
Rick
99 EC 200
06 RM 250
AMA D36
375X
OTHG
375S

***Thanks for the support : Twin Air /O'Neil Racing / Race 100% / Matrix Concepts / ODI / Mika Metals
Reply With Quote
  #16  
Old 01-03-2012, 10:59 PM
GMP's Avatar
GMP GMP is offline
Senior Member
 
Join Date: Jul 2006
Location: Jefferson Twp., NJ
Posts: 7,597
Default

Its not stamped where it should be, but it looks like an A size.

Leo, most unusual for GoFasters. Mark and Steve have always been prompt to answer the phone when I call, and have gone out of their way to help me personally. Perhaps there is an email issue. Holiday season doesn't help either. Please try another media before going public next time, thanks.
Reply With Quote
  #17  
Old 01-03-2012, 11:19 PM
lankydoug lankydoug is offline
Senior Member
 
Join Date: Jul 2010
Posts: 491
Default

Leo makes a good point based on his experience and seems to be trying to be helpful. I too have had issues with GoFasters and prefer Halls even when Halls has to go through GoFasters.
Reply With Quote
  #18  
Old 01-04-2012, 02:15 AM
AMCQ AMCQ is offline
Member
 
Join Date: Oct 2006
Location: West Midlands UK
Posts: 2
Default

Quote:
Originally Posted by GMP View Post
Its not stamped where it should be, but it looks like an A size.
thanks, I was thinking I was going mad not being able to find any marking.

Are you concluding it is an A from the piston marking?
__________________
Alastair Mc

GG EC200 2003
Reply With Quote
  #19  
Old 01-04-2012, 06:17 AM
GasGas's Avatar
GasGas GasGas is offline
Senior Member
 
Join Date: Aug 2007
Location: Nova Scotia, Canada
Posts: 694
Default

My 2011 is stamped B inside the left side power valve cover.
__________________
2018 EC 300
Reply With Quote
  #20  
Old 01-04-2012, 09:15 AM
GMP's Avatar
GMP GMP is offline
Senior Member
 
Join Date: Jul 2006
Location: Jefferson Twp., NJ
Posts: 7,597
Default

While not perfect, GF has kept the parts train moving from Spain to the USA so the brand would not die here. Just be happy you have the option to talk to and deal with(for now) the parts importer directly. Try that with KTM, been down that road.
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
"attn." "new England Boys" RONALD BRUNDIGE General Discussions & Announcements 9 11-17-2008 09:19 PM
"B" piston in an "A" bore? Kokanee Enduro Engine - 2 stroke 6 09-04-2006 08:10 PM
Recommendation: add "Injury/Recover" and "Riding Techniques" sections MattR Suggestion Box 2 07-18-2006 10:19 PM




All times are GMT -5. The time now is 08:07 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org