Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Engine - 2 stroke

Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 03-26-2015, 12:11 AM
jmdcr50 jmdcr50 is offline
Member
 
Join Date: Nov 2011
Posts: 41
Default crank

Hey all could somebody tell me what tork you use ti tighten the right side of the crank. The tork # I have 70 ft pds . I had my kid help me and I could not tighten it to that spec..


Reply With Quote


  #2  
Old 03-26-2015, 02:50 AM
(F5)'s Avatar
(F5) (F5) is online now
Gold Level Site Supporter
 
Join Date: Jul 2006
Location: Wellington New Zealand
Posts: 2,052
Default

Till it just strips and back a bit. That way you know its really tight.
No its OK, the knowing you've helped is its own reward.
__________________
'07 EC300 GG
'14 TXT250 GG
'? 496 CPI Cheetah RZ/RGV hybrid
'22 765 Street Triple RS
'21 XTrainer
'69 Stinger T125 Suzuki
'23 TRS 250RR (it's a Trials thing)
Reply With Quote
  #3  
Old 03-26-2015, 05:18 AM
Jakobi's Avatar
Jakobi Jakobi is offline
Super Moderator
 
Join Date: Oct 2010
Location: Australia
Posts: 7,994
Default

98Nm, reverse thread.
Reply With Quote
  #4  
Old 03-26-2015, 06:43 AM
jmdcr50 jmdcr50 is offline
Member
 
Join Date: Nov 2011
Posts: 41
Default

Yes 98nm is about 72 ft pd. and I am using a some copper to bind the gears. just wondering if I should put a cheater bar on the tork wrench
Reply With Quote
  #5  
Old 03-26-2015, 07:14 AM
Jakobi's Avatar
Jakobi Jakobi is offline
Super Moderator
 
Join Date: Oct 2010
Location: Australia
Posts: 7,994
Default

Is it a lack of leverage, or that the engine is on the bench and the whole thing turns as you try to torque it up? If its the later, an extension won't help.. a jig to mount the engine on a vice will..
Reply With Quote
  #6  
Old 03-26-2015, 01:55 PM
jmdcr50 jmdcr50 is offline
Member
 
Join Date: Nov 2011
Posts: 41
Default

Yup pretty much what you said Jakobi . I'll work at it thanks. You always seem to have answer Jokobi lol for everybody on this site
Reply With Quote
  #7  
Old 03-26-2015, 05:55 PM
Jakobi's Avatar
Jakobi Jakobi is offline
Super Moderator
 
Join Date: Oct 2010
Location: Australia
Posts: 7,994
Default

All you really need is a length of something and a couple of long bolts, few washers, and rig something to hold the engine via the mounts.. or drop the engine back in the frame for a bit if its nice and clean.
Reply With Quote
  #8  
Old 03-26-2015, 10:16 PM
jmdcr50 jmdcr50 is offline
Member
 
Join Date: Nov 2011
Posts: 41
Default

ya I put it back in the frame and got it all sorted out.
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Crank Remover and Crank Installer tools for EC250 Fabry Enduro Engine - 2 stroke 5 06-25-2013 08:24 PM
gas gas ec 200 crank chinesegav United Kingdom 5 11-27-2012 07:49 PM
Crank bearings Marki Enduro Engine - 2 stroke 2 12-29-2011 12:47 PM
Crank it up! Rick Pictures & Videos 2 04-09-2011 01:36 PM




All times are GMT -5. The time now is 09:34 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org