Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Chassis & Body

Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing.


Reply
 
Thread Tools Display Modes
  #1  
Old 03-02-2009, 08:27 AM
johns2394 johns2394 is offline
Member
 
Join Date: Oct 2008
Posts: 31
Default Oversized discs for supermoto gas gas Wheels?

Oversized discs for supermoto gas gas Wheels? can they be bought where to get them from are the supermoto hubs same as offroad ones


Reply With Quote


  #2  
Old 03-02-2009, 10:38 AM
slocalspode's Avatar
slocalspode slocalspode is offline
Senior Member
 
Join Date: Mar 2007
Location: Southern Kalifornia
Posts: 450
Default

You might try here first:
http://www.moto-master.com/default.php
search by bike name. There is a USA
dealer, if you are in the States.
You might look up motostrano.com and
give them a call.
GoFasters may also be able to get you
a real GasGas brand front rotor as well
as a caliper relocation bracket.
As far as I know. The SuperMoto wheel
hubs are the same as Enduro wheel hubs.
If you have not found it yet. Supermotojunkie.com
has lots of general SuperMoto information.
Not a lot on GasGas though.
Here is my set up for a 1998 EC250SM with the
Marzocchi 50mm forks and Brembo caliper.

Yours is most likely going to be different.
Good luck, Jeff
Reply With Quote
  #3  
Old 03-11-2009, 09:24 AM
johns2394 johns2394 is offline
Member
 
Join Date: Oct 2008
Posts: 31
Default

still struggling with finding a rotor and bracket or any UK place that i can get these from what about genuine gas gas parts any help please
Reply With Quote
  #4  
Old 03-11-2009, 11:03 AM
cal_tony cal_tony is offline
Senior Member
 
Join Date: Oct 2008
Location: California Central Coast
Posts: 170
Default

I previously posted about my inability to find Supermoto wheels and brakes for my 450FSE. I ended up by going with a 17" KTM front wheel, hub and rotor. For the rear, I went with DRZ stuff. Parts for this setup are available anywhere.

For a front bracket to mount the rotor,I took Jeffs advice and bought a Motomaster bracket so I could mount a 320mm rotor to the front fork.

Tony
Reply With Quote
  #5  
Old 03-12-2009, 06:16 PM
cookeye cookeye is offline
Member
 
Join Date: Mar 2008
Location: UK
Posts: 8
Default

On my 2002 ec i used a ccm 320mm front disc listed for most of the supermoto ccm's including the 404, my 404 had WP forks the same calliper braket as my 2002 ktm and same as my 04 404 ccm, this allso bolted up to my gasser
hth
mick
Reply With Quote
  #6  
Old 03-13-2009, 09:22 AM
johns2394 johns2394 is offline
Member
 
Join Date: Oct 2008
Posts: 31
Default

does the ccm disc fit the gas gas wheels then or did you just use the ccm adapter bracket
Reply With Quote
  #7  
Old 03-13-2009, 11:50 AM
cal_tony cal_tony is offline
Senior Member
 
Join Date: Oct 2008
Location: California Central Coast
Posts: 170
Default

As I'm not sure what model GG your talking about I wouldn't know what 320mm bracket you would need. In fitting the 320 rotor to the caliper you would need a specific bracket to match the fork to the caliper. Matching the rotor to the hub is one factor. The other is matching the fork to the caliper and extending it by enough to accept the 320mm rotor. In looking at jeffs bracket, it appears that the bracket just extends the components by enough to fit the larger rotor. My fork is the standard Shiver 45mm connected with a Nissen bracket to a Nissen caliper. The Motomaster bracket for that set up is different than Jeffs. My motomaster bracket part#2110036 attaches to the fork and completely replaces the standard Nissen bracket.

Depending on the fork and caliper that the CCM uses would determine whether or not their extension bracket would work with your setup.

Tony
Reply With Quote
  #8  
Old 05-10-2012, 06:41 PM
wakeymatt wakeymatt is offline
Member
 
Join Date: Apr 2012
Posts: 66
Default

has anybody ever tried drz wheels ?

"Update" I tried a friends and the front fit but the back was way to wide sprocket to disc !

Last edited by wakeymatt; 05-15-2012 at 07:29 PM.
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Discs crossover johns2394 Enduro Chassis & Body 2 12-25-2008 09:59 AM
Front oversized Rotors cal_tony Enduro Chassis & Body 0 11-01-2008 11:57 AM




All times are GMT -5. The time now is 10:11 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org