|
General Discussions & Announcements General Announcements, General Questions, e.g. What bike do I buy?, etc. |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
Have any of youse guys had a .....
chain on your GG with out a master link? I was going service my linkage today and went to remove the master link and there tweren't none....this is the stock chain. I have heard of it on street bikes but never on a dirt bike.
__________________
Alan 14GasGas ec300r |
#2
|
||||
|
||||
My 07 came with a rivited link also. In the past I always installed the rivited link to give a piece of mind of not losing the clip while out on the trail.
__________________
07 GG EC 300 05 KTM 250 exc 99 KTM 640 enduro |
#3
|
||||
|
||||
My 07 250 didn't have one.
|
#4
|
|||
|
|||
Well, now you have.
Time to get your grinder out Oh, and you'll need a new master link. Tony |
#5
|
||||
|
||||
Quote:
Thanks, gents.
__________________
Alan 14GasGas ec300r |
#6
|
||||
|
||||
i believe theres actually a tool for uninstalling and reinstalling isnt there? my buddies all ride crotch rockets and none of the have master links but they have this speciol tool to punch out and then re-rivet and link. ive thought about trying one but @ 100 bucks i cant afford one!
__________________
Le Crutan 98 ec250 sixdays, doma, eline pipe guard, zokes shivers from a cr250,fredette racing chain slider, protaper withbarkbusters (SOLD) FOR THE SECOND TIME 07 EC300 polisport headlight, acerbis taillight ltr pv cover and case saver,trailtech endurance,120z fww, g2 throttle,xr chain puck: |
#7
|
||||
|
||||
You can not reuse the rivited link because you have to grind the heads off first before you can use a chain breaker.
You will have to buy another link.
__________________
07 GG EC 300 05 KTM 250 exc 99 KTM 640 enduro |
#8
|
|||
|
|||
I use a punch never had a problem.
|
#9
|
|||
|
|||
I didn't mean to be flippant about your observation.
I wasn't expecting it to be an endless chain either. There are lots of posts on Thumpertalk.com especially in the DRZ section. (they come with the same Regina chain) about removing and replacing the endless chain and also lots of info about the tools required to replace the removed link with another press fit link. I just use my $16 Harbor freight 4" grinder. Pick any link and grind it flush. Than use a thin punch and pop the link. when replacing the link with either type replacement make sure you use lots of grease and put back the orings front and back. I use vice grips to repress the new link on. With the orings in place, it takes quite a squeeze to put it back together. To avoid having to do it again I just use replaceable links. Tony |
#10
|
|||
|
|||
On the subject of masterlinks, I install mine with the clip on the inside of the chain. It is a pain to install but if it were ever to come off, the master works its way out and falls off, no big deal. If the master lets loose installed with the clip to the outside the results could be very expensive.
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
We can't trust those KTM guys | kendunn | Pictures & Videos | 6 | 03-15-2012 10:56 PM |
Colorado Guys | F_G | Enduro Intake/Carburetion - 2 stroke | 3 | 05-14-2010 06:28 PM |
ok guys i need help again....... | dank | Enduro Chassis & Body | 16 | 05-08-2010 05:55 PM |
WER Damper guys | skid jackson | General Discussions & Announcements | 11 | 07-30-2008 07:39 PM |
Don't hate me, I need you guys | thelonius | General Discussions & Announcements | 6 | 11-18-2007 01:53 PM |