|
|
|||||||
| Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
 |
|
|
Thread Tools | Display Modes |
|
#1
11-25-2008, 07:57 AM
|
||||
|
||||
kick starter help
Hey guys, I have an 01 xc300 and have been destroying my rh boot, I bought the yz kick starter , new, for a 00 or 01 yz250 and the spline on
my 300 is smaller than the spline on the yz kick starter. any thoughts ? I will post up some pixs this weekend, just wanted to get you guys opinion. thanks in advance jay
__________________
broken down over 60 slow rider.. 
|
|
#2
11-25-2008, 08:05 AM
|
||||
|
||||
|
I don't think it's the kickstarter destroying your boot. My guess is that you are hitting the boot on the footpeg when you kick the bike over.
My right boot is a little chewed up and that is why I think it is happening. It's not enough that it's an issue for me.
__________________
2004 GasGas DE250
|
|
#4
11-25-2008, 08:32 AM
|
||||
|
||||
|
yes... it where i am hitting the peg with the shorter kicker.
I have lost a pretty good chunk off my boot. My hips are gone with arthritis and I try to point my toe out, but it is just not working. thanks guys, i will get the later model. jay
__________________
broken down over 60 slow rider..
|
|
#6
06-19-2011, 03:09 PM
|
||||
|
||||
|
Quote:
i think it is 03 and newer yz
|
|
#7
06-20-2011, 07:14 PM
|
||||
|
||||
|
I have the same kick starter on my 07, and not only is it a better length, but it is a better design than the stock one as well. It's sealed on top so dirt and moisture doesn't get in to the pivot as easily. If I have to replace my 2010's kicker, it'll be a YZ one going on.
Wes.
__________________
13 EC200 Race 10 EC250 Six Days (SOLD) 07 EC250 (for sale) 85 RZ500 75 XL250 71 CB100 08 DRZ70 (son's)
|
|
#8
06-20-2011, 09:10 PM
|
||||
|
||||
|
I put one on my bike,I had the short stock one which was good enough to easily kick my 300 but wearing out .Really like the longer yz one though as I never come close to whacking the footpeg.Highly recommend for that alone ,now just to see how it holds up
Stoby Also I got it from honda east toledo for around 75 bucks-cheapest i found anywhere and it shipped fast Last edited by Stoby; 06-20-2011 at 09:19 PM. Reason: forgot to add where i bought it
|
|
#9
07-27-2011, 09:59 PM
|
|||
|
|||
|
Turns out mine was missing ball and spring. I fixed that for @1.50, so far so good, although it took some patience to get the damn thing on! I ended up using a 7mm socket to hold the ball/spring in place and then slid it over the kicker arm. Without that I may have burned the damn thing down!
No matter now though. I am in engine rebuild mode. Seems I may have toasted the crank. Like they say, "If ya aint breaking it, ya aint riding hard enough!" Thanks for the replies all!!!
|
|
#10
12-08-2011, 09:08 PM
|
|||
|
|||
|
got a 07 yz kickstarter and when i put it on my 07 ec300 it slides back and forth on the shaft. the splines dont go all the way through like on the GG one so the bolt just tightens up on the shaft but the starter will slide back and forth. Any of you all run into this
|
|
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Kick Starter ? | rockrider1 | General Discussions & Announcements | 1 | 11-04-2010 08:49 AM |
| 07 250 Kick Starter | prk03 | Enduro Engine - 2 stroke | 2 | 03-28-2009 10:59 PM |
| Kick starter? | 2 strokes 4 life | Enduro Engine - 2 stroke | 2 | 09-08-2008 09:47 PM |
| Kick starter probs | peterr | Enduro Engine - 2 stroke | 4 | 10-03-2007 05:36 AM |
Linear Mode
