GasGas Riders Club Forum  

Go Back   GasGas Riders Club Forum > GasGas Enduro Technical Forums > Enduro Engine - 2 stroke

Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc.


Reply
 
Thread Tools Display Modes
  #31  
Old 08-23-2018, 06:25 PM
memphis2857 memphis2857 is offline
Senior Member
 
Join Date: Aug 2011
Posts: 896
Default

Quote:
Originally Posted by john r b View Post
Chris, how was the tko??


Hardest one yet. My effort was dismal at best. Lack of preparation and lack of seat time really reared it’s ugly head. I was about 2 miles from the end of TKO 1 when the track workers convinced me that continuing on was not a good idea.


Sent from my iPhone using Tapatalk


Reply With Quote


  #32  
Old 08-23-2018, 06:26 PM
memphis2857 memphis2857 is offline
Senior Member
 
Join Date: Aug 2011
Posts: 896
Default

Quote:
Originally Posted by Desert Silver View Post
Is that the Pro X one? wiesco lists a forged piston for the Gas Gas 300 ATV but only list a Pro X cast piston for the EC300


Came in a wiesco box. Might just give Halls Cycles a call and they will set you right up


Sent from my iPhone using Tapatalk
Reply With Quote
  #33  
Old 08-23-2018, 06:27 PM
Jacob 'Berg Jacob 'Berg is offline
Senior Member
 
Join Date: Mar 2014
Location: Scottsdale, AZ
Posts: 410
Default

https://www.ebay.com/itm/TOP-END-KIT...gAAOSwX99Zn9Ha

This is the route I usually go. Great kit with everything you need for a good price.
Reply With Quote
  #34  
Old 08-23-2018, 06:51 PM
john r b's Avatar
john r b john r b is offline
Platinum Level Site Supporter
 
Join Date: Aug 2012
Location: Warrenton,Va
Posts: 893
Default

Piper, kicking ass on pricing again!!
__________________
'12 XC 200 TTX
'15 XC 250E
Reply With Quote
  #35  
Old 08-23-2018, 06:53 PM
john r b's Avatar
john r b john r b is offline
Platinum Level Site Supporter
 
Join Date: Aug 2012
Location: Warrenton,Va
Posts: 893
Default

Quote:
Originally Posted by memphis2857 View Post
Hardest one yet. My effort was dismal at best. Lack of preparation and lack of seat time really reared it?s ugly head. I was about 2 miles from the end of TKO 1 when the track workers convinced me that continuing on was not a good idea.


Sent from my iPhone using Tapatalk
Better safe,than sorry 6 feet under.,
__________________
'12 XC 200 TTX
'15 XC 250E
Reply With Quote
  #36  
Old 08-27-2018, 02:50 PM
Desert Silver Desert Silver is offline
Member
 
Join Date: Mar 2014
Posts: 27
Default

Quote:
Originally Posted by Jacob 'Berg View Post
https://www.ebay.com/itm/TOP-END-KIT...gAAOSwX99Zn9Ha

This is the route I usually go. Great kit with everything you need for a good price.
Thanks!! That's what I'll use as my son is going to sell it after I get it back together. Thank You again!!
Reply With Quote
  #37  
Old 09-12-2018, 02:40 PM
Desert Silver Desert Silver is offline
Member
 
Join Date: Mar 2014
Posts: 27
Default

Putting it back together so far has been way easier than trying to take it apart. Just as a side note, my son is selling his 15 Gas Gas EC300E. It's registered for the street in Kali which is rare. PM me if any are interested and I'll supp;y the info. By the way, the main reason he's selling is he wants a 2018.
Reply With Quote
  #38  
Old 09-13-2018, 01:24 PM
Desert Silver Desert Silver is offline
Member
 
Join Date: Mar 2014
Posts: 27
Default

Well this ISN'T going to plan. The damn ring locating pins are in the wrong place. The pins are so close in the clocking as to be right over each other. I already installed on the rod and there's a few surface scratches from trying to install the pin clips though they're not on any surface that contacts the cylinder. I was too trusting that it was the right part and didn't check it out before hand. Damn Ebay!!
Reply With Quote
  #39  
Old 09-13-2018, 03:05 PM
Desert Silver Desert Silver is offline
Member
 
Join Date: Mar 2014
Posts: 27
Default

Here's the original and the new one. There's a booster port located right where the locating pins are.
Attached Images
File Type: jpg DSCF0605.jpg (117.8 KB, 27 views)
File Type: jpg DSCF0606.jpg (111.7 KB, 25 views)
Reply With Quote
  #40  
Old 09-14-2018, 09:55 PM
Jacob 'Berg Jacob 'Berg is offline
Senior Member
 
Join Date: Mar 2014
Location: Scottsdale, AZ
Posts: 410
Default

Do the rings pass over the booster port at BDC?
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
2012 and 2011 ec300e Phaeton Used Bikes 0 10-04-2017 10:08 AM
2011 EC300e part out Mick Parts 35 03-16-2017 07:00 PM
First Ride on '15 EC300E celester Enduro Intake/Carburetion - 2 stroke 2 10-08-2016 04:48 PM
2011 EC300E maiden voyage Bobt250 General Discussions & Announcements 24 01-06-2011 01:33 PM




All times are GMT -5. The time now is 05:03 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org