|
Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Ec300 2015 stalls on high revs
Hi guys, after 2 weeks that my ec300 won't run and left with open fuel valve it stalls on high revs.
On low and middle range it runs fine... only when I try to go up to the high range it stalls... The carb tuning seems to be fine because it never happened before and I didn't change the the jetting. Thanks for the help. |
#2
|
||||
|
||||
Stalls in common useage means stops completely. I'll assume you mean stutters badly.
1st off change the plug and consider the plug cap. Ignitions are so good these days its easy to forget plugs can have all sorts of odd faults. Then clean the carb out carefully. Also check fuel line isn't kinked. In-line filters love to create these kinks in short lines. Check gascap breather.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#3
|
||||
|
||||
Check what F5 has suggested.
Also... Fuel starvation? Is the carb getting plenty of fuel? There's a gauze filter on the petrol tap inside the tank, remove/inspect/clean. Also check the fuel tank breather in the filler cap is working and isn't blocked, if no air's getting into the tank petrol won't flow out easily. I assume air filter is clean? Is the tail pipe clear? I've seen tail pipes blocked with wadding that's come loose. Bikes start but won't rev at high rpm as they can't flow the exhaust gas. It's simple but can cause some strange effects! Good luck. |
#4
|
|||
|
|||
Did you find the problem? I just bought a 2013 EC 300 that is doing the same thing and I am not sure what the problem is. It cuts out at high revs. I set my needle position to the third notch from the top. It was on the second.
|
#5
|
||||
|
||||
If it loses power over a few seconds and stalls, I'd be looking at a fueling problem, maybe fuel starvation.
If it stalls quickly/sharply I'd be looking at an electrical/ignition problem. Good luck, Dave. |
#6
|
|||
|
|||
My '03 suddenly developed a severe break up in the mid range and would not rev high at all. Traced it to a failed voltage regulator.
A friend's '05 lost power, the engine sort of bogged in the mid range and wouldn't rev out. The power valve linkage had become disconnected (bolt fell out). Good luck.
__________________
'15 YAMAHA WR250F, '75 YAMAHA TY80 Gone: '00 380 EXC, '03 EC300, '07 YZ250, '07 250 XC-W, '08 YZ450F, '12 CRF250R |
#7
|
||||
|
||||
Erm. . So the cdi doesn't use the lighting/ battery charge coils at all so no need for regulator. That would only be the case for a dc powered cdi like an Ignitech. (Not sure about very latest models).
The earthing point for the coil and frame is there though so it could have been the issue.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#8
|
|||
|
|||
Quote:
|
#9
|
|||
|
|||
Quote:
__________________
'15 YAMAHA WR250F, '75 YAMAHA TY80 Gone: '00 380 EXC, '03 EC300, '07 YZ250, '07 250 XC-W, '08 YZ450F, '12 CRF250R |
#10
|
||||
|
||||
Haha. That's a cute fault.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Overheating on high load and revs only, what could it be ? | poelinca | Enduro Engine - 2 stroke | 18 | 07-11-2017 05:45 AM |
Really sputters at high revs now | motopsycho87 | Enduro Electrical & Wiring | 11 | 11-14-2013 02:04 PM |
Engine won't run at high revs | motopsycho87 | Enduro Engine - 2 stroke | 36 | 08-28-2013 04:37 PM |
Sputters at high revs... | motopsycho87 | Enduro Electrical & Wiring | 9 | 06-21-2013 10:12 PM |
Low speed high gear stalls in v.slippery conditions | stay_upright | Enduro Engine - 2 stroke | 5 | 04-02-2010 12:48 PM |