|
Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Nissin Rear brake pump
My ec 300 GG 2009 nissin rear brake pump is leaking.
Is there a sealing or piston kit on the market? I found nothing in the spare parts list where? price?
__________________
Husqvarna TE 300 |
#2
|
||||
|
||||
There might be a closer dealer to you than these guys but I have found them helpful.
GasGasUK e-mail mail@gasgasuk.com phone (44) 01298 766813 For other parts. Trialendurodirect or call them 01298 766 813
__________________
HuskyDude 10 EC300XC 08 TE510 07 TXT 280 77 TY175 |
#3
|
||||
|
||||
These people may be able to help, not sure if you know about them or not, but regardless, they are closer than most other dealers...
http://www.gasgas-online.de/catalog/index.php |
#4
|
|||
|
|||
I found one for 30€ there is no part number - say my dealer.
Another question: How can I adjust my foot brake lever in a ideal position for me. The f... spring pull the lever everytime up. Is there some aftermarket lever?
__________________
Husqvarna TE 300 |
#5
|
||||
|
||||
There is an aftwermarket lever but that will not solve your problem. You should cut a few mm from the master cyl rod to allow the pedal to be adjusted lower. Common mod we all do.
|
#6
|
|||
|
|||
now I changed the sealing but I can't get out the air in the system
I have to much play at the lever my normal procedure 1. press the piston back complete in the rear caliper 2. open the screw in the rear caliper - fit a 6mm tube 3. press the lever the brake fluid and air comes out 4. close the screw 5. release the lever 6. open the screw 7. press the lever 8. close the screw 9. release the lever and so on at the end I apply the lever so long until the piston press the brake pads close to the disk normaly it works in this way there is no more leaking !!!!! but every time I have to much play in the lever When I start the precedure new - new air bubbles comes out of the little screw any idea?
__________________
Husqvarna TE 300 |
#7
|
|||
|
|||
Today I hang up the rear caliper and pump 1/2 h without closing/open the screw.
I see many air bubbles.Then the system was clean. Now I have only 1 cm play in the lever. May be there is a problem with the brake pump and underpressure. The pump pulls air inside when I close the screw and release the lever. But no leaking. I don't know. A new pump is to expensive now.
__________________
Husqvarna TE 300 |
#8
|
||||
|
||||
Read this and try a search next time, lots of good info here. Good Luck!
http://www.gasgasrider.org/forum/showthread.php?t=8068 |
#9
|
|||
|
|||
thanks but my technical english isn't so good - I will improve it - I swear .
__________________
Husqvarna TE 300 |
#10
|
||||
|
||||
Can anyone tell me how to get a seal kit for a 07 rear break pump.. notting on the parts list.. can they even be serviced? Im going to open mine during the week, so any advice would be great? ? Thanks
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Rear brake adjustment | Silver | Enduro Chassis & Body | 5 | 06-03-2009 07:50 AM |
Rear Brake Caliper | blitz11 | Enduro Chassis & Body | 11 | 10-28-2008 03:38 PM |
Nissin Rear Brake rebuild kit? | Berkyboy | General Discussions & Announcements | 4 | 09-13-2007 06:41 AM |