GasGas Riders Club Forum  

Go Back   GasGas Riders Club Forum > GasGas Enduro Technical Forums > Enduro Engine - 2 stroke

Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 02-24-2008, 08:24 PM
g dirt g dirt is offline
Member
 
Join Date: Feb 2008
Location: Orillia, Ontario
Posts: 3
Default 07 GG300EC - small hole at btm. of engine?

What is the small threaded hole for on the underside of the engine? It is located between the oil drain plug and the crankcase drain plug.

Also what is an approved sparkplug by NGK or Champion that is equal to the denso plug that comes stock on the 300?


Reply With Quote


  #2  
Old 02-24-2008, 08:46 PM
GMP's Avatar
GMP GMP is offline
Senior Member
 
Join Date: Jul 2006
Location: Jefferson Twp., NJ
Posts: 7,597
Default

I beleive its used in mfg for a jig. The older cases ran the ignition drain to a hole like that but the hole in my '07 250 is blind. NGK BR8EG or cheaper BR8ES works fine.
Reply With Quote
  #3  
Old 02-25-2008, 08:12 PM
GasGas's Avatar
GasGas GasGas is offline
Senior Member
 
Join Date: Aug 2007
Location: Nova Scotia, Canada
Posts: 695
Default

What do you guys use for a plug in your 125 GMP? I've been using a BR9ES. Just wondering if a 8 wood last better in the woods. The 9's seem fine on the track but not so much in the woods.
Reply With Quote
  #4  
Old 02-25-2008, 09:16 PM
GMP's Avatar
GMP GMP is offline
Senior Member
 
Join Date: Jul 2006
Location: Jefferson Twp., NJ
Posts: 7,597
Default

The 125 is my nephew's bike, and sometimes when running real slow and technical stuff it will foul a BR9. The BR8 works better in these conditions. If its open enough where the bike is on the pipe a lot the 9 gives no problems and we run it. Jetting is very good, and the bike makes good low end for a 125. I suspect that some head work may clean this up.
Reply With Quote
  #5  
Old 02-26-2008, 05:48 AM
GasGas's Avatar
GasGas GasGas is offline
Senior Member
 
Join Date: Aug 2007
Location: Nova Scotia, Canada
Posts: 695
Default

Thanks, I find the same with the 9's. I will be trying an 8 at the next scramble.
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Hole In Cylinder PEB Enduro Engine - 2 stroke 1 09-07-2010 10:19 AM
help guys,which bike gg250ec or gg300ec nickp General Discussions & Announcements 9 08-04-2010 08:22 PM
Small bike and ATV ban. Ud_luz General Discussions & Announcements 22 05-04-2009 01:06 PM
Cyl/Head o-rings why so small Treesmacker Enduro Engine - 2 stroke 9 02-19-2009 11:09 PM
M6 hole under engine? moff747 Enduro Engine - 2 stroke 2 03-19-2008 10:48 PM




All times are GMT -5. The time now is 10:54 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2022, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org