|
Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Rpm drops on idle
So. I have this gasgas 250 from 2003. I just renovated the engine With new connecting Rod, all gaskets, piston, piston ring, main bearing etc. The bike was not idling before the overhaul and I still have a problem.
I have a ne1c needle set to first position, a 40 pilot and a 168 main. Nr 6 slide. Ive set the slide height to 1 mm, set my float level, put AS to 1,5. Idle screw out. Here is what happens. It fires up, and as Long as i keep reving slighty its ok, when i release it Will idle fine for a few seconds, after That time the rpm suddenly drops. Way low, to a Point where its barely staying Alive. And most Times it dies. What is this? Happens evvvery time. I cant figure it out. |
#2
|
|||
|
|||
Maybe worth trying the needle in pos 2 or 3 ??
__________________
03 ec300 honda cr500 94 |
#3
|
||||
|
||||
You have played with the idle screw?
__________________
02 300ec- 50mm Marzocchi cc forks, 2010 plastic. Now a 250cc. |
#4
|
|||
|
|||
Had the needle on third to begin with. Same story
|
#5
|
|||
|
|||
Yeah ive toyed with it a little but no real results. Doesnt the idle screw just push your slide up/down? How high can u set the slide, and what happens if you go too high ? I would have somewhat better result idling with the slide higher. But it ends up dying from too much gas it seems, so not really an option
|
#6
|
||||
|
||||
Do you have another needle to play with, as my 300 won't idle unless it has the JD red needle in, and then will idle all day but when it was a 250 it didn't like the red needle and would die after 30 seconds or so..
__________________
02 300ec- 50mm Marzocchi cc forks, 2010 plastic. Now a 250cc. |
#7
|
|||
|
|||
Actually i dont.. Would you recommend me one ? I would appreciate an ebay link or something similar.
|
#8
|
||||
|
||||
Sorry no, our resident forum jetting juru (jakobi) will be along to recommend the right needle.
__________________
02 300ec- 50mm Marzocchi cc forks, 2010 plastic. Now a 250cc. |
#9
|
||||
|
||||
I know nothing about the early models. I've posted loads of info on how to fine tune your bike based on how it behaves though.
Check the jetting database for ideas of good starting points. |
#10
|
|||
|
|||
I Will defenitly read through it. Just sometimes the language acts as a barrier for Deep understanding.
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
02 400 will not idle | jason r | Enduro Engine 4 stroke (including EFI & Exhaust) | 7 | 11-18-2013 04:14 PM |
300 won't idle. Please help!! | stemplin | Enduro Intake/Carburetion - 2 stroke | 32 | 04-05-2012 07:28 AM |
Power drops with revs | swazi_matt | Enduro Electrical & Wiring | 0 | 10-09-2011 05:52 AM |
Bad idle | Madhead | Enduro Intake/Carburetion - 2 stroke | 1 | 08-11-2011 06:20 AM |
can,t get idle up | geno | Enduro Intake/Carburetion - 2 stroke | 1 | 04-18-2010 08:49 PM |