Why Doesn't GasGas Have Online Factory Service Manual Like this?

[Moto7man]

Whay doesn't GasGas have an online Factory Service-Shop Manual and site like these? The shop manual below is 351 pages with labeled digital photos!

http://www.endurofactory.nl/pdfs/201..._250R-310R.pdf

http://www.husqvarnafactory.nl/pdf/index.htm

[Moto7man]

Has anyone seen a current GasGas factory shop manual like these Husqvarna manuals? I'm curious because the factory and or the bigger dealers must have one, right???

[djroggen]

Originally Posted by Moto7man

Has anyone seen a current GasGas factory shop manual like these Husqvarna manuals? I'm curious because the factory and or the bigger dealers must have one, right???

The answer to that is no.

[Tool Guy]

Guys, are there any published torque values for the fasteners used on the engine and frame? I'm an old, experienced wrench, but there are torque/tightening differences that I would like to be aware of.

Thanks, Gordon

[2taddict]

Originally Posted by Tool Guy

Guys, are there any published torque values for the fasteners used on the engine and frame? I'm an old, experienced wrench, but there are torque/tightening differences that I would like to be aware of.

Thanks, Gordon

If this helps these are for EC / MC / SM / 125 / 250 / 300 - 2005
I wouldn't think there would have been to many changes since then.

FRAME N-m

Brake caliper mounting bolt????25
Disc mounting screw???..???...10
Engine mounting bolt?..????.?36
Front axle bolt????...?????51
Front brake hose mounting bolt?..?6
Suspension clamp bolt??..????29
Steering nut?????...?????98
Rear axle nut???????.???98
Rear brake pedal bolt???????9
Subframe bracket bolt????.??26
Rear shock absorber bolt?????39
Rear drive plate nut???.????29
Spokes?????????????1.5
Steering stem nut????..????.4
Torque rod bolt??.???????81
Rear linkage bolt???...?????81


ENGINE N-m

Cylinder head screws??????..25
Cylinder nut??????????.25
Engine drain plug????????20
Kick-start pedal bolt???????20
Kick-start pedal nut???????25
Gearshift pedal bolt???????15
Spark plug????????..??.27
Water pump cover drain plug???9
Crankcase screws????????10
Starter pedal plate screw?????.8
Ignition motor stator screws????8
Ignition motor coil nut??????.40
Selector spring fixing screw????15
Primary nut??????????..40
Clutch spring screws???????10
Valve control support screws???..10
Valve control nuts????????..8
Reed valve screws????????..10
Thermostat housing screws????..10
Clutch housing screws??????..10
Valve housing screws???????.8
Ignition housing screws??????.10

http://www.manualslib.com/manual/386...s-Ec-2005.html

[webmaster]

Be warned - some of the torque values in the manual are incorrect. Here is torque table for some fasteners that GMP put together long ago :

http://www.gasgasrider.org/torque_table.jpg

jeff

[2taddict]

http://www.manualslib.com/manual/386...s-Ec-2005.html

Well I guess that manuals not worth a pinch of shit then eh.

[Todd5774]

Originally Posted by Moto7man

Whay doesn't GasGas have an online Factory Service-Shop Manual and site like these? The shop manual below is 351 pages with labeled digital photos!

http://www.endurofactory.nl/pdfs/201..._250R-310R.pdf

http://www.husqvarnafactory.nl/pdf/index.htm

Not this old chestnut again...

[twowheels]

Originally Posted by Moto7man

Has anyone seen a current GasGas factory shop manual like these Husqvarna manuals? I'm curious because the factory and or the bigger dealers must have one, right???

Not again ... Still.

Originally Posted by Todd5774

Not this old chestnut again...

[Jakobi]

I just use a ktm manual.. yeah I do!