|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
2018/19 aftermarket cylinder head
Has anyone tried this head?
https://www.2strokeheads.com/index.p...formance-heads I contacted them to get one and the price changed from the listed $150 to $325 so I want to make sure it?s worth the coin before getting one |
#2
|
||||
|
||||
Everyone raves about this head.
The $150 is to modify the OEM head. The other is a full billet head. |
#3
|
|||
|
|||
Best money you will spend on your bike. He has 3 different options available. The cheapest being reshaping the stock head, next would be modifying your stock head to accept his insert, and most expensive would be the full billet head. I went for the billet head and it was worth every penny. Power improved across the board drastically, and overheating is near impossible now.
Sent from my iPhone using Tapatalk |
#4
|
|||
|
|||
Thx for the input guys.
It could be due using my phone but the website showed $150 for the full head. I figgered for that price give it a shot (and it seemed cheap) but their website dosnt do international and I got correct price buying via email. Just abit short of cash right now so wanted some opinions before spending that much. I have a GP250 and straight off idle the bike is doughy as so hoping the head will improve that area |
#5
|
|||
|
|||
I had them cut a stock head for 100 octane fuel. Noticeable improvement to bottom and mid-range power. They will also cut your stock head to accept different inserts. This is nice as you can run a higher compression insert for higher altitudes.
|
#6
|
|||
|
|||
Quote:
__________________
Sponsors: http://www.evolutionsuspensionproducts.com/ http://www.sportbiketrackgear.com/ Blog: http://www.speedofarrival.com/ |
#7
|
|||
|
|||
Quote:
Also, did you have to go with shorter head bolts? These are both problems I ran into when trying to run the piece of shit XIU head and considering this head is twice the price, I want to know what I'm getting into. Thanks.
__________________
Sponsors: http://www.evolutionsuspensionproducts.com/ http://www.sportbiketrackgear.com/ Blog: http://www.speedofarrival.com/ |
#8
|
||||
|
||||
I don't think they make a billet head for the pre '17 bikes.
They would modify your existing head. |
#9
|
|||
|
|||
Quote:
Have you changed the stock needle jet yet? That thing is garbage and robs tons of bottom end power Sent from my iPhone using Tapatalk |
#10
|
|||
|
|||
Have a 42 pilot and NECW on 3rd clip installed. Plug chops say it?s rich but less power if I lean it any more
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
TSP head mod - 2018 EC250 | Gibnut | Enduro Product Reviews | 27 | 04-27-2019 09:25 PM |
Aftermarket Plastics for 2018/2019 EC Models | RudolfHucker | Enduro Chassis & Body | 0 | 11-08-2018 07:12 AM |
Swopping 1997 Cylinder head with 2005 head | EC250 | Enduro Engine - 2 stroke | 10 | 12-15-2015 10:13 AM |
Coolant leaking through cylinder head socket-head bolts. | GGRider01 | Enduro Engine - 2 stroke | 5 | 10-17-2015 07:38 PM |
VHM aftermarket cylinder head | GG27 | Enduro Engine - 2 stroke | 2 | 11-02-2009 04:15 AM |