|
General Discussions & Announcements General Announcements, General Questions, e.g. What bike do I buy?, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
How to stop the pinging
Getting sick of chasing my tail with this bike. I'm currently running the jd red needle, 3rd clip with 172 main and 42 pilot. I only just moved needle from 2nd clip to 3rd position as I'm trying to stop the pinging on deceleration. It's terrible. I haven't ridden it on the 3rd clip yet but running the bike in the yard it's still pinging. It's a19 gasgas 300 with the head cut. Not sure what the squish is at but it was done by a reputable business who have done my other bikes. I'm running at between sea level and 500 meters. Any helpful advice would be appreciated. Thanks
|
#2
|
|||
|
|||
Jetting Thread
Here is the jetting thread, it includes specific settings for year model and riding conditions.
http://www.gasgasrider.org/forum/sho...t=2162&page=35
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#3
|
|||
|
|||
Yes I have looked at the jetting thread previously. Tried a few settings based on other riders settings but haven't been able to find that perfect setting yet. I'll keep delving into the info. This bike just seems to be very tricky. It's frustrating the hell out of me.
|
#4
|
||||
|
||||
Are you sure it's pinging and not something else?
Pinging is associated with a noise under acceleration. Maybe the pipe rattling? |
#5
|
|||
|
|||
Pipe Mount
Sometimes that rubber pipe mount will break and you will get a rattle under acceleration.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#6
|
||||
|
||||
I've found with mine that the decel noise was associated too much slide height at idle. (Idle screw turned too far in). You might need to tweak needle? Pilot? air screw? to get the proper idle with less slide height/idle screw.
__________________
Noah 2000 EC250 with 2011 transformation kit, KYB SSS forks, MN street title 16' Ski-Doo XS Renegade X 1200 4T 16' Specialized Fatboy trail 02' ZRX 1200r R.I.P. 72' Olds 500ci, Batten Heads, Street/Drag car, former CarCraft magazine centerfold (has-been) 15' TW200 |
#7
|
|||
|
|||
Definitely not the pipe rattling. Thanks nknudsen. I'll have a mick around with the pilot. I take it I should go up in pilot size?
|
#8
|
||||
|
||||
Actually lean out. Play around with leaner air screw, needle position, pilot, one or a combination should raise your idle so you can lower the slide/idle screw.
__________________
Noah 2000 EC250 with 2011 transformation kit, KYB SSS forks, MN street title 16' Ski-Doo XS Renegade X 1200 4T 16' Specialized Fatboy trail 02' ZRX 1200r R.I.P. 72' Olds 500ci, Batten Heads, Street/Drag car, former CarCraft magazine centerfold (has-been) 15' TW200 |
#9
|
||||
|
||||
What slide?
|
#10
|
||||
|
||||
__________________
Noah 2000 EC250 with 2011 transformation kit, KYB SSS forks, MN street title 16' Ski-Doo XS Renegade X 1200 4T 16' Specialized Fatboy trail 02' ZRX 1200r R.I.P. 72' Olds 500ci, Batten Heads, Street/Drag car, former CarCraft magazine centerfold (has-been) 15' TW200 |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
New 19 EC300 pinging | pigpen966 | Enduro Engine - 2 stroke | 7 | 10-09-2021 02:40 AM |
My either Crazy or that knocking /pinging is BAD... | Scar13 | Enduro Engine - 2 stroke | 40 | 05-05-2012 11:53 PM |
Pinging? | Neil E. | Enduro Engine - 2 stroke | 22 | 04-24-2012 07:44 PM |
FAQ Input : Pinging when backing off the throttle. | jeffd | Enduro Engine - 2 stroke | 0 | 08-02-2006 11:47 AM |