|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#11
|
||||
|
||||
I have never liked those roller bearings, pain in the ass to get off the crank and from my testing don?t last as long as ball bearings. I always replace them with ball bearings when I get the chance even though logic says the rollers should last longer. If it has those sealed type mains I have seen them suck in a gut full of water through their seals and then rust away because the water can’t evaporate out. And that is pretty good hours out of a racer!
But after that bit of info I am wondering where else water made it too?
__________________
Back on a gassy! 2018 EC300! 🤘 Txt 280 07 to make me feel like a gumby again |
#12
|
||||
|
||||
When you replace the roller with a ball bearing, do you use the same part number as the clutch side or is it a different bearing?
|
#13
|
|||
|
|||
Quote:
__________________
Sponsors: http://www.evolutionsuspensionproducts.com/ http://www.sportbiketrackgear.com/ Blog: http://www.speedofarrival.com/ |
#14
|
||||
|
||||
Yeah i had drowned mine in a creek. About 4 years ago.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#15
|
||||
|
||||
Different part number when I get home from night shift I?ll dig it out
__________________
Back on a gassy! 2018 EC300! 🤘 Txt 280 07 to make me feel like a gumby again |
#16
|
||||
|
||||
Well the right crank end nut is putting up a fight. Even once I read the manual and started turning it the right way. Goodly amount of heat. My rattle gun isn't the best so I may take the bike to a mates.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#17
|
||||
|
||||
Quote:
(I did the same thing, except mine came loose right away) Zman: On the '01 200, both crank bearings are the same. RB |
#18
|
||||
|
||||
Put up a fight but finally off with better rattle gun and bigger bar through small end so it didn't bounce so much.
Then it was the swingarm bolts turn. Slowly slowly, biggy hammer. He did lend me a crankcase splitter too. Flash.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#19
|
|||
|
|||
I bet you remember for next time.
In fact;I guarantee it. |
#20
|
||||
|
||||
Hard spirits required. Broken cage if you look.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Crank bearing failure .WTF ? | Getoviq95 | Enduro Engine - 2 stroke | 2 | 04-16-2017 01:27 AM |
gas gas stator failure ? | klex | Enduro Engine 4 stroke (including EFI & Exhaust) | 2 | 08-24-2016 12:29 AM |
Ignition side crank bearing failure? | wence | Enduro Engine - 2 stroke | 37 | 06-16-2016 07:21 PM |
Rebuild failure | Capz85 | Enduro Engine - 2 stroke | 44 | 04-15-2016 12:24 PM |
Crank Remover and Crank Installer tools for EC250 | Fabry | Enduro Engine - 2 stroke | 5 | 06-25-2013 07:24 PM |