|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Looks Like Oily Stuff
as the title says, i have black oily stuff coming from my exhaust, have i put too much oil in with the petrol,??????????????????? or is natural for a 2 stroke????????????????? gas gas ec250, o dont think it's the rings going as there is lots of compression, still there and loads of power, starts fisrt kick every time hot or cold,
any help would be appreciated thanks |
#2
|
||||
|
||||
thats pretty common in 2 strokes, what ratio do you premix? m 300 says 2% but i mix it closor to 5% id rather have spooge than need a top end.
__________________
Le Crutan 98 ec250 sixdays, doma, eline pipe guard, zokes shivers from a cr250,fredette racing chain slider, protaper withbarkbusters (SOLD) FOR THE SECOND TIME 07 EC300 polisport headlight, acerbis taillight ltr pv cover and case saver,trailtech endurance,120z fww, g2 throttle,xr chain puck: |
#3
|
||||
|
||||
Some oils "spooge" more than others.
I have found that Motul is the worst. Motorex has zero spooge. Check your muffler packing for oil saturation. FYI:You should never jet your bike using spooge as a guide. |
#4
|
||||
|
||||
My bike always spooges. No worries though.
|
#5
|
||||
|
||||
I have had trouble with synthetic oil spooging - I have much less trouble with YamaLube
__________________
“There are only three sports: mountain climbing, bull fighting, and motor racing. All the rest are merely games.” – Ernest Hemingway "is the bike ok" "(groannnnnnnnnnnn)" "no seriusly is it ok?????" "crap the shrouds cracked" |
#6
|
|||
|
|||
What kind of bike do you have, EC or DE/XC? I have never been able to jet my XC to not "spooge", I think it has to do with the MC ignition box that is used on it. My kids EC runs the same jetting (both run excellent) and doesn't drip at all. We run Royal Purple 100% synthetic, 40:1
__________________
jeff '00 XC250 (mine) LTS front and rear suspension, power valve cover, carb jet kit and rear chain glide, RB Designs head mod, BRP tall triple clamp, backyard foot-peg lowering conversion. '04 EC250 (the kids) (he can do his own mods haha!) Last edited by jostby; 11-18-2008 at 11:28 AM. Reason: spelling |
#7
|
||||
|
||||
I run my bike a bit rich in terms of jetting and thats why i get spoonge. You can jet any bike so it wont spoonge.
__________________
2002 Gasgas EC250 (gone not forgotten) 2012 Ktm 300xc 2001 Gasgas EC300 Lifes journey is not to arrive safely at the grave in a well preserved body, But rather to skid in sideways totally worn out shouting holy cow what a ride !!!! |
#8
|
|||
|
|||
Quote:
i'm running 20ml to 1litre at the moment, as the guy said who i bught it off, my local bke shop said 25 to 1 it's ec250 |
#9
|
||||
|
||||
Another area that builds up spooge is the left side p/valve area. You might want to clean that out also. Could be very messy if it has not been cleaned in a while.
__________________
Rick 99 EC 200 06 RM 250 AMA D36 375X OTHG 375S ***Thanks for the support : Twin Air /O'Neil Racing / Race 100% / Matrix Concepts / ODI / Mika Metals |
#10
|
|||
|
|||
please help wheres that
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Do I really need this stuff? | thelonius | General Discussions & Announcements | 16 | 12-07-2007 08:57 PM |