GasGas Riders Club Forum  

Go Back   GasGas Riders Club Forum > GasGas Enduro Technical Forums > Enduro Intake/Carburetion - 2 stroke

Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc.

Thread Tools Display Modes
Old 02-05-2021, 02:29 AM
(F5)'s Avatar
(F5) (F5) is offline
Gold Level Site Supporter
Join Date: Jul 2006
Location: Wellington New Zealand
Posts: 1,664

Originally Posted by Jim Cook View Post
I believe that's N1EF that you meant to say in the statement above. I agree with you about the advice to get rid of it and go to a better jet needle (such as the NECW, or some other recommended needle. )

Or a twig approximately the right length that seems smaller at one end than the other. Either way around will be better.

'07 EC300
496 CPI Cheetah RZ/RGV hybrid
675 Street Triple R
RS125 framed MB100 racer
Stinger T125 Suzuki
Reply With Quote

Old 02-18-2021, 06:07 AM
Doc Brown Doc Brown is offline
Senior Member
Join Date: Dec 2017
Location: Austria, Europe
Posts: 576

That your carb doesn't react on the As has nothing to do with the float height nor with the needle.

First look what is installed and let us know, then adjust float height and when you do so check float valve. Check how far the slide is lifted by the idle screw.

Turning in the AS all the way should stall the engine.
Reply With Quote
Old 02-19-2021, 05:57 PM
Gasser Nate's Avatar
Gasser Nate Gasser Nate is offline
Senior Member
Join Date: May 2010
Posts: 478

It kind of does though, when the wrong needle is used, I am looking at you N1ef...
It forces the user to lift the slide too far to compensate for the overly rich first section in a vain attempt to get it to idle.
This then lifts the slide past the effective range of the air screw.
Back on a gassy! 2018 EC300! 🤘
Txt 280 07 to make me feel like a gumby again
Reply With Quote
Old 02-22-2021, 10:19 AM
Trailrider Trailrider is offline
Senior Member
Join Date: Oct 2006
Posts: 161
Default Pilot jet story

Here is the whole story. The jet needle wore out on my stock carb. I replaced it with a counterfit Chinese carb.The pilot jet was clogged up even though it was clean when I put it in Jetting is JD jet kit. Adjusting the float bowls was no help. Poor weather has slowed me down.
I plan to reinspect the pilot jet and main jet, and give the whole carb a good cleaning, I think the commies left pieces of metal inside.
If this doesnt work I will either buy a real carb from JD ($300) or part it out.
Any suggestions appreciated.
Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Similar Threads
Thread Thread Starter Forum Replies Last Post
1 pilot jetsize equils how many pilot screw turns mattlloyd50 Enduro Intake/Carburetion - 2 stroke 2 04-14-2013 04:46 AM
pilot jet? BryanMcc Enduro Intake/Carburetion - 2 stroke 12 04-07-2013 09:53 PM
pilot jet vs. air screw question stainlesscycle Enduro Intake/Carburetion - 2 stroke 4 06-27-2010 03:51 PM
42 pilot skid jackson Enduro Intake/Carburetion - 2 stroke 6 03-08-2009 07:56 PM
Pilot macho comacho Enduro Intake/Carburetion - 2 stroke 5 02-06-2009 03:54 PM

All times are GMT -5. The time now is 12:39 PM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Copyright 2009 -