|
"Wanted to Buy" & "Want To Trade" Bikes or Parts |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Wanted : 45mm Marzocchis
One of mine is cracked at the bottom...
Anyone have a decent set that they want to part with? Thanks, Richard Exclaim Enduro Tours www.ExclaimTours.com |
#2
|
||||
|
||||
Let me check upstairs in the garage, tonight.
__________________
13 GasGas 300XC, CLake and now Rekluse 17 Beta 430 RRS, Clake 19 Vertigo 300 03 H-D Nightrain www.newoodsriders.com You Can't Out Run Death Forever But You Can Make the BASTARD Work For It! Enjoy Life, Have Fun and Play Hard |
#3
|
||||
|
||||
Can't you just replace the lug?
__________________
Rick 99 EC 200 06 RM 250 AMA D36 375X OTHG 375S ***Thanks for the support : Twin Air /O'Neil Racing / Race 100% / Matrix Concepts / ODI / Mika Metals |
#4
|
||||
|
||||
That is a lot more involved than you think. Done incorrectly, you ruin the entire assembly.
|
#5
|
||||
|
||||
I was under the impression the fork tube is threaded into the lug, sealed by a o ring. Then again I may be wrong.
__________________
Rick 99 EC 200 06 RM 250 AMA D36 375X OTHG 375S ***Thanks for the support : Twin Air /O'Neil Racing / Race 100% / Matrix Concepts / ODI / Mika Metals |
#6
|
||||
|
||||
Unfortunately I've been through this unsuccessfully, even working with a local machinist. Les warned me it could be a disaster. The lower tube is threaded in the foot, with loctite, and a has setscrew with a point that rolls a couple threads on the tube. That is the tricky part. This damaged thread area has to be precisely machined out with an end mill through the small hole and cleaned with a pick. Then the tube must be held secure, heat, and with some luck its off. Any thread distortion combined with the loctite makes a mess of the foot threads and its impossible to remove after a few turns.
I've never seen a GG Zoke foot separately anyway so you shouldn't have to sweat this option anyway. |
#7
|
||||
|
||||
Thanks for the insight.....learn something everyday.....I assumed it was a do-able.
__________________
Rick 99 EC 200 06 RM 250 AMA D36 375X OTHG 375S ***Thanks for the support : Twin Air /O'Neil Racing / Race 100% / Matrix Concepts / ODI / Mika Metals |
#8
|
||||
|
||||
Have a set off an 2005 300 EC. These were tuned by LTR, and have the stock 42 in them. Would like to get 150.00 + Shipping. We're are you from so that I can get you a cost.
__________________
13 GasGas 300XC, CLake and now Rekluse 17 Beta 430 RRS, Clake 19 Vertigo 300 03 H-D Nightrain www.newoodsriders.com You Can't Out Run Death Forever But You Can Make the BASTARD Work For It! Enjoy Life, Have Fun and Play Hard |
#9
|
|||
|
|||
I have a pair of 48mm Zokes for sale but shipping would be expensive.
__________________
4 strokes are only good for power generators |
#10
|
||||
|
||||
Wow! That is a great deal...less than I paid to have mine revalved.
__________________
Believe nothing, no matter where you read it or who has said it, not even if I have said it, unless it agrees with your own reason and your own common sense. [Buddha] |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Marzocchis on GG300 EC 2011 | Mr B | Enduro Suspension | 2 | 02-07-2012 10:02 AM |