|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
power valve triangle plate
So while trying to undo the nut that holds the link rod in place I have broken the lug off the triangle actuator plate. I'm not sure if I can repair, maybe drill the plate and put a bolt through?
Where are people in Australia buying parts from now that gasgas Australia is no longer the importer. New importer still has no parts site online. Cheers. |
#2
|
||||
|
||||
Been there done that. What did I do? Think I welded something back in from the back. A while back and a few beers tonight.
Find an old time engineer dude and give him whatever he asks.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#3
|
|||
|
|||
Many warnings here about that.
For those that haven't heard...torch the nyloc nut to melt the plastic before trying to remove it. |
#4
|
|||
|
|||
__________________
2010 GasGas EC300 Nambo |
#5
|
|||
|
|||
I think jay has knocked it on the head and is out of the game now.
Close motocycles in marrickville (Sydney) will get the part you require. |
#6
|
||||
|
||||
The pin is just tack welded into the plate from what I remember. Should be able to have a decent welder do the same for you, making it better than new.
|
#7
|
||||
|
||||
Yeah I used a pretty dreadful welder (me) but its still hanging in there just fine. I had to add a washer so it turned without getting hung up.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#8
|
||||
|
||||
I'd probably just blow a hole through the whole tab if I tried.. or spatter it with bird poo...
|
#9
|
||||
|
||||
Ahh. So you know my secret techniques.
Actually I just took my old gasless mig to the tip. I feel much more competent with my new welder. Although I'm yet to spark it up. I've had it over a month. . . Can't believe it. Too much else on.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#10
|
||||
|
||||
Wait until you try alloy...one sec theres a weldpool then "pffft"....gone...all gone...
Quite demoralising if you thought you could weld reasonably with stick and mig...
__________________
2013 ec200r |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Ec 300 power valve | Jonisaacson17 | Enduro Engine - 2 stroke | 11 | 07-18-2016 09:01 PM |
Loss of power - suspect power valve | Jonny Halls | Enduro Engine - 2 stroke | 4 | 01-22-2013 09:56 AM |
power valve nut | bonkeye | Enduro Engine - 2 stroke | 4 | 10-11-2012 06:40 PM |
Is this power valve lever plate wrong? | mark250ec | Enduro Engine - 2 stroke | 2 | 09-06-2011 05:39 PM |
Power valve | bens25au | Enduro Engine - 2 stroke | 2 | 02-09-2008 11:02 PM |