#21
|
||||
|
||||
Thank you!
__________________
All healed up, and ready to burn some fat. |
#22
|
||||
|
||||
you bet.. glad to help...
__________________
broken down over 60 slow rider.. |
#23
|
||||
|
||||
Make sure that the plastic retainer that goes on the end of the throttle cable after the spring is seated in the slot on the needle "bolt" the little 6mm screw that sucures the needle into the slide. I have seen those not seated properly and will throw you way off track... thinking the jetting is not correct.
Just my.02 Jay,,,nice chart you posted. Thanks
__________________
Rick 99 EC 200 06 RM 250 AMA D36 375X OTHG 375S ***Thanks for the support : Twin Air /O'Neil Racing / Race 100% / Matrix Concepts / ODI / Mika Metals |
#24
|
||||
|
||||
Quote:
|
#25
|
||||
|
||||
Quote:
175 main jet 35 pilot jet #8 slide The needle is unconfirmed, since I was unsuccessful figuring it out, on my own. Either way, I still need the #7 slide from the Kawi. I just figured out what I thought was a lowly owner's manual, is in fact a service manual. It's full of all kinds of information. I guess I should have flipped through, anyway. Hand written notes, include: 180 main 35 pilot N1EF #2 clip from top #7 slide On the next page, handwritten: 180 main 35 pilot N1EG top clip #6 valve cut slide To me these only mean that more than person, or same person were making carb magic...I don't know. I barely understand the corralation between these parts. At least I know this much, so far. Now I have to figure out the needle question.
__________________
All healed up, and ready to burn some fat. Last edited by bowhunter007; 10-24-2012 at 05:38 AM. |
#26
|
||||
|
||||
The needle will have the code etched into it just below the clips. They can be a little hard to read at times.
|
#27
|
||||
|
||||
Quote:
my 01 came factory with a 35 pilot .. i had never seen a pilot that small.... mine had a n1ee in it..factory rick.. thanks.. i love that chart..
__________________
broken down over 60 slow rider.. |
#28
|
||||
|
||||
Is there some sort of magic trick to removing the needle, from the slide? I am missing something, don't know what. I would rather not break anything
__________________
All healed up, and ready to burn some fat. |
#29
|
||||
|
||||
Stolen from an earlier post on DBW today!
You need to use one hand to bind up the spring and plastic retainer towards the top of the throttle cable. Then push in slightly and the cable will come out of the locating groove in the 6mm retainer. Once you have the slide out you need a 6mm socket to undo the retainer in the top of the slide. Tip it upside down and the needle and clip slide out as one. To remove the clip I like to put the needle on a clean solid surface and gentle push each side of the clip unti it starts to pop off. Be careful not to launch it into the abyss! Putting it back together is the opposite. Take care not to over tighten the 6mm retainer in the slide. Bind the spring up and make sure the cable slides in and mounts properly into the slide. Then when you let the spring back down make sure the little lug in the plastic part locates into the groove in the 6mm retainer. Test the throttle action before taking off for a test ride! |
#30
|
||||
|
||||
Quote:
__________________
All healed up, and ready to burn some fat. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Powervalve issue? | SpeedyManiac | Enduro Engine - 2 stroke | 222 | 11-01-2023 07:03 PM |
Overflow issue and bog | forgiven | Enduro Intake/Carburetion - 2 stroke | 4 | 10-05-2011 09:20 AM |
jetting - idle issue. | stainlesscycle | Enduro Intake/Carburetion - 2 stroke | 7 | 12-30-2009 02:47 AM |
clutch issue | boostedte37 | General Discussions & Announcements | 2 | 11-09-2009 06:58 PM |
ec 400 gearbox issue | Paul Somerville | Enduro Engine 4 stroke (including EFI & Exhaust) | 3 | 09-05-2009 10:17 AM |