|
Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc. |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
How to set float level. Revisited.
A while back, I posted a link on how to set your float level.
I finally found it after a long search. Here it is again for those that need to have their's reset.. http://www.dirtridersinternational.c...?TOPIC_ID=2292 Last edited by gasgasman; 08-25-2007 at 09:08 PM. |
#2
|
||||
|
||||
For some reason the photos won't come up.
Here they are in the order that they appear in the instructions. (Float assembly pivot pin not shown.) (Fuel inlet needle shown with Viton (rubber) tip. The Viton is used to isolate the fuel inlet needle from vibration and to create a better seal against the fuel inlet valve seat.) |
#3
|
|||
|
|||
The first link no longer works.
I have checked and adjusted float level on other carbs, so could someone post some basic instructions with dimensions? Thanks, Josh |
#4
|
||||
|
||||
Try this http://www.keihin-us.com/am/_media/pdf/slide_valve.pdf
Float height is mentioned on the right.
__________________
'05 Gas Gas 300 '97 Aprilia Pegaso 650 '99 KTM 200 '95 ish XR630 (died many times in Oz) |
#5
|
|||
|
|||
Quote:
of the float as shown in the picture. |
#6
|
|||
|
|||
help on float height
Hi can anyone advise me on the correct float height for my year 2000 ec 300.
|
#7
|
||||
|
||||
16mm to the best of my knowledge.
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com |
#8
|
||||
|
||||
Sounds right, but a rule of thumb is to have the seam in the float parallel to the carb body.
__________________
2004 GasGas DE250 |
#9
|
||||
|
||||
I set the floats on my GG by simply tilting the carb and closing the float gap until it stopped puking fuel at a 20 to 30 degree angle, then took a test ride and checked it at W/O.
May sound stupid bit it works. A friend has a 09 that still drools when on the side stand. |
#10
|
|||
|
|||
Do this guideline also work for the newest generation of PWK.
I check my PWK 38 today - the float look totally different - only plastic no metal. The GG 300 2009 Nambo is leaking on the trailer. The float hight was 11mm - now I go to 14mm. I can't test it until now. My shock is in service.
__________________
Husqvarna TE 300 |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
EC300 Idle Revisited. | Ud_luz | Enduro Intake/Carburetion - 2 stroke | 35 | 01-07-2011 07:39 PM |
Rear wheel spacers revisited. | Ud_luz | Enduro Chassis & Body | 9 | 09-13-2010 08:01 PM |
Zokes oil level? | jostby | Enduro Suspension | 2 | 06-20-2009 11:29 AM |
Fork oil level ? | Brian VT | Enduro Suspension | 4 | 03-10-2009 08:57 PM |
WP Fork Oil Level | MattR | Enduro Suspension | 11 | 08-02-2006 10:40 AM |