|
Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Best Long Term Rotors OEM or Aftermarket
I am soooo close to finishing a complete the overhaul of my 2001 EC200. This has been a top to bottom affair. I just got my Ohlins suspension back from Borelli in Mendota IL. Highly recommended!
One of the last things to buy is replacement rotors. I am hoping that someone has some long term experiance with Moose or Galfer or some of the others. It seems like the Moose solid mudfree might be good. Galfer, for the money better be great. My OEM's *10 years old* are still striaght, but badly grooved. I blame this on very poor caliper preventive maintenance. I will be writing up the details of my caliper overhaul, but it seems most people ignore the boots, sllides, clips, etc. Soooo any very positive recommendations out there berfore I click buy it now? Hope all goes well for everyone! |
#2
|
||||
|
||||
rotors can last almost forever if the slides are greased and maintained. i always give the calipers a quick pull before a ride to make sure they're not siezed...
i've had good luck with the moose solid rotor.
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com |
#3
|
||||
|
||||
+2 on the Moose solid rotor (rear).
No overheating issues even in the 100F summers here in Texas. |
#4
|
|||
|
|||
I ordered up the solid rear moose last night. 119, free shipping seems to be the standard on ebay. My front rotor seems pretty good at the moment, but I will need a new one during my winter maintenance. I'm working on what I hope becomes a sticky for caliper overhaul. I've been building a cross over list for all the replacement small parts. GG charges a mint for these, when most of them, the clips, boots, pins, seals, are either CR or KDX cross overs for the Nissin caliper.
|
#5
|
||||
|
||||
The Moose is fine, but I have had great luck with the GG solid rotors for about $30-40 less if you can still get them and at that price. I have a few, one on each of my rear wheels, and they are holding up very well.
|
#6
|
|||
|
|||
I definitely would have tried the OEM solid rear, especially to save a few dollars. I am only about 300% overbudget on the restore of my 250. Woa is my pocket book. Rather happy are Hall's and Go Fasters!!! I'll be rebuilding my 200 this winter. I'll look to the OEM rear disc on this one and run a long term comparo. Thanks Glenn!
__________________
2001 GG EC250, 2001 GG EC200 1980 KDX 175, 2002 KDX 220, 1979 KZ 1300 Vroom Vroom Some day a brand new bike... some day... |
#7
|
|||
|
|||
Im running the moose wave rotor up front and a slotted rotor out back. They feel very predictable when stopping. I havent used the solid rotors, cause it just doesnt get enough of the wet stuff that falls from the sky where I live.
|
#8
|
|||
|
|||
I'm kinda afraid to run the solids myself as I have boiled the brake fluid on my 97 and 03 regularly with the vented rotors.. I think I have an issue dragging the brake at times...
__________________
Steve 16 Beta 350rr 04 KTM 525 sx/exc gone 03 KTM 625 sxc-rehab unit-did its job and now gone 03 GG 250 ec-gone 97 GG 250 ec Gone |
#9
|
||||
|
||||
Contrary to popular belief, solid rotors are actually better for high heat/ dry conditions.
The solid rotor pulls the heat away from the pads. As a result, less heat to the brake fluid. |
#10
|
|||
|
|||
I would love a list of crossover parts for brake rebuilds!
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
03 EC200 clutch stuck after long sit | lankydoug | Enduro Engine - 2 stroke | 4 | 03-07-2011 10:47 AM |
New guy, long time lurker | East_TN_GG | General Discussions & Announcements | 9 | 07-01-2009 08:37 AM |
brake rotors.... | infected | Enduro Chassis & Body | 8 | 11-21-2008 04:53 AM |
Front oversized Rotors | cal_tony | Enduro Chassis & Body | 0 | 11-01-2008 10:57 AM |
shiftshaft/long ride in 1st! | Cruiser | Enduro Engine - 2 stroke | 10 | 05-30-2007 07:21 AM |