#41
|
||||
|
||||
The rear wheel on my 09 KTM measures 157mm from inside rotor face to inside sprocket face, so its too wide
|
#42
|
||||
|
||||
I asked my brother to measure a Husky wheel so we will see where that goes.
|
#43
|
|||
|
|||
Back in the old days,, on the smackover forum,, We had this discussion and somebody sold wheel spacers to make jap wheels fit.. I think from a 96 cr250 this was for the older GG bikes with the wp forks. 20mm axle I believe. motowest maybe? might have been the kx/kdx, but rather sure they were honda wheels.. but then back then you could buy a set of SM wheels for your Gasgas for under a grand..
__________________
Steve 16 Beta 350rr 04 KTM 525 sx/exc gone 03 KTM 625 sxc-rehab unit-did its job and now gone 03 GG 250 ec-gone 97 GG 250 ec Gone |
#44
|
|||
|
|||
Honda used the 20mm rear axle from the late 80's to 99. I think it was the late 90's the wheel kits were from.. but then again.. this was back in like 01..
__________________
Steve 16 Beta 350rr 04 KTM 525 sx/exc gone 03 KTM 625 sxc-rehab unit-did its job and now gone 03 GG 250 ec-gone 97 GG 250 ec Gone |
#45
|
||||
|
||||
FYI, late model Husky rear wheel (WR250, TE450, etc.)
rotor to sprocket surface - 152mm axel OD - 25mm |
#46
|
||||
|
||||
We all should bug Mark at Gofasters, to get with the factory and get us some spare wheels "AT A REASONABLE PRICE" even if we need to pre order them.
I'd be ok with taking one unassembled, if it will cut cost. What do you guys think? |
#47
|
||||
|
||||
i would say yes its a great idea if it wasnt for the resonable price thing. i bet mark could probably get wheels at a discounted price but theyll still not be in the resonable realm just for the simple fact that no manufacturer exception of DNA wheels of course is going to come in at less than close to a grand, for some reason this always seems to be the magic number. that is why i thought if we could find a set that would fit with mere spacer modifications it would be very cheap for all of us but its not panning out to well
__________________
trevor |
#48
|
|||
|
|||
My Ktm complete rear wheel Cush drive type minus the sprocket carrier was $425.
__________________
Steve 16 Beta 350rr 04 KTM 525 sx/exc gone 03 KTM 625 sxc-rehab unit-did its job and now gone 03 GG 250 ec-gone 97 GG 250 ec Gone |
#49
|
|||
|
|||
And it was a dirt star rim like the 03 gg had.
__________________
Steve 16 Beta 350rr 04 KTM 525 sx/exc gone 03 KTM 625 sxc-rehab unit-did its job and now gone 03 GG 250 ec-gone 97 GG 250 ec Gone |
#50
|
|||
|
|||
Bump
Just seeing if this is a dead issue or what? Anyone make any headway yet. I found an old kdx rim but when I went to get it, drum brakes. Pre '92 I guess
__________________
2007 EC450FSR 2003 XR100R 1980 Z50R |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
plastic fitment | randy | General Discussions & Announcements | 11 | 02-03-2010 03:03 PM |
air filter fitment | wence | Enduro Engine - 2 stroke | 6 | 12-23-2008 09:49 PM |
Gaerne SG 10 Fitment Question | Boomhauer | Enduro Product Reviews | 5 | 12-16-2008 07:04 PM |
Aftermarket wheels. | Ud_luz | Enduro Chassis & Body | 3 | 12-08-2008 05:59 PM |
Gear box mess (circlip fitment) | craigyboy | Enduro Engine - 2 stroke | 2 | 10-28-2008 10:11 AM |