|
General Discussions & Announcements General Announcements, General Questions, e.g. What bike do I buy?, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Anyone installed Scorpion Racing Radiator cages on a 2010 model?
I am curious as to whether anyone on this forum has installed these cages on a 2010. I'll post a few pics of my install.
__________________
2010 GasGas EC 300 Nambotin Replica #141 2006 Honda XR650R Supermoto |
#2
|
|||
|
|||
I have had very poor luck with Scorpion stuff. The fit is really hit or miss.
If I was in the market for rad braces, I would wait for the Enduro Eng braces to hit the market in a couple of weeks. Their stuff always fits "right". |
#3
|
||||
|
||||
Ive got them on my Nambo , this is the 3rd set ive had , had them on my 06 , my 09 , now the 10 Nambo , Perfect fit all 3 times for me
Opps , are you talking about the Guard or the Frame ? They make more than one model Ive got the whole gaurd with the frame cross brace , http://scorpionracing.ca/index.php?p...mart&Itemid=26 and it is great
__________________
2011 Nambo Out on the Trails on Vancouver Island , BC Steve |
#4
|
|||
|
|||
braces
I have the rad braces that use the stock louvers. Tricky to put on but worked fine once I stopped following the directions and did it my own way. Make the bike a bit wide but are very solid.
Cheers Rick
__________________
Track-N-Trail Cycle LLC trackntrailcycle.com 2011 Beta 400 RR (sorry ) 2010 GAS GAS XC 300 2007 KTM 200 XC |
#5
|
|||
|
|||
I was referring to the Radiator frames. I'm going to show my install pics in the Nambotin thread because they are specific to that bike. Apparently all Nambotins have their louvers on upside down. The frames fit great and I feel confident knowing my rads aren't going to suffer in a tumble.
__________________
2010 GasGas EC 300 Nambotin Replica #141 2006 Honda XR650R Supermoto |
#6
|
||||
|
||||
I have them on my six days. As I recall the directions weren't very good, you have to remove the bottom outside rubber grommet all together and the rad shrouds have to be stretched a little to line up the lower bolt hole. Also, I think I had to modify the plastic louvers or swap them from one side to the other so they would clear the lower crossbar on the cages. These are very solid cages though, and have done a great job protecting the rads so far.
Wes.
__________________
13 EC200 Race 10 EC250 Six Days (SOLD) 07 EC250 (for sale) 85 RZ500 75 XL250 71 CB100 08 DRZ70 (son's) |
#7
|
||||
|
||||
I put a set on NamboTrev's and they fit great!
__________________
Claude 2019 XC300 2010 Nambotin 300 sold '07 EC300 sold '06 EC300 sold '78 Suzuki RM250C2 '75 Yamaha YZ250B sold |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Scorpion Racing Radiator Frames and Skid Plates | Kurdt | Enduro Chassis & Body | 8 | 08-16-2010 05:30 PM |
Racing Model graphics | TooFastTim | General Discussions & Announcements | 2 | 10-24-2009 04:58 PM |
jetting for new 300 racing 2010 | fabulous furry | Enduro Intake/Carburetion - 2 stroke | 9 | 08-11-2009 09:28 AM |
2010 Race model sneak peek | Skidad | General Discussions & Announcements | 6 | 02-28-2009 04:22 AM |
Radiator Cages | PEB | Enduro Chassis & Body | 23 | 11-27-2008 07:35 PM |