|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
HELP NEEDED!!! Clutch issue
Hi I'm new to the forum.
I have a issue with my GG EC200 ( 2006 ) Clutch was dragging bad and because I bought it not long ago I thought I will change the clutch and a new basket just because it looked a bit worn. I also changed the clutch line to a braided one and change fluid because not sure how long it was last serviced. Clutch still drags but also having trouble bleeding clutch I have hardly any pressure and I've used a vacuum line to draw air out but still no pressure on lever. Thanks Last edited by GGEC; 10-13-2019 at 10:28 AM. |
#2
|
||||
|
||||
1. Did you use DOT4 or mineral oil in the clutch cylinder? The wrong fluid will cause internal leaking.
2. you could have air in the clutch master cylinder. 3. What clutch plates did you use? (some of the aftermarket pates are thicker than stock and cause drag.) |
#3
|
||||
|
||||
Minor drag can be cured with different oil. In my bike Motul Transoil (std) drags enough not to be able to kick in gear. But the Transoil Expert version is fine..
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#4
|
|||
|
|||
First check the adjuster screw position on the clutch lever. Wind it fully in and try if it helps.
|
#5
|
|||
|
|||
Hi guys thanks for the reply much appreciated.
I do use MOTUL mineral oil so I will try the other version thanks (F5). I adjusted the screw also whilst trying other things but with no difference Thanks Mikeyx. Man I have used Motul mineral oil but i will try other version like ( F5 ) said. I have DP clutch kit which was supplied by a GASGAS dealership, could these be the issue? the clutch was dragging before I changed it? I tried again tonight to bleed the system I had constant air bubbles coming out even with the use of the vacuum bleeder. I also tried the old fashion way of bleeding only using the master open/closing the nipple but still no luck. I also changed the seals on the slave (bottom slave) to be sure it wasn't leaking through but still no luck. anymore ideas guys I would appreciate it. Thanks |
#6
|
|||
|
|||
I used a syringe and pushed fluid up from the bleeder to the master. Worked very well.
|
#7
|
||||
|
||||
Have a dig through this post which has measurements
http://www.gasgasrider.org/forum/sho...ighlight=Cr250
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#8
|
|||
|
|||
If you're bleeding put some plumbers teflon tape around the nipples otherwise it can drag in a little bit of air through the loose threads and never bleeds the air out cause it keeps getting more in!
|
#9
|
|||
|
|||
All sorted!!!
Hi guys thank you everyone that helped me out, its all sorted now.
When rebuilding the master a small part of the seal has come off (perhaps rolled on itself inside the bore) and blocked the port hole, so it would pump but wouldn't return. The new rebuild kit seems to be way too tight to be the correct one so I'm going to speak to the supplier to confirm it was right. For now I have used the old plunger and it has worked a treat after bleeding the line to slave first then bleed the master after connecting it together then bleed the whole system, bit of a hassle way of doing things but I wanted to be sure it was going through correctly. I also replaced the washer on the thrust bearing with a 2mm spacer to bring the hub closer which has helped a lot. Recommending doing this. It basically takes up the 1mm-1.5mm slack so the clutch is touching where as before it would have to take that slack first before pushing clutch springs. |
#10
|
|||
|
|||
Quote:
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Clutch issue | KsGman | Enduro Chassis & Body | 12 | 08-01-2018 06:47 PM |
Clutch issue | Longo117 | Enduro Engine - 2 stroke | 17 | 10-16-2017 11:39 PM |
Clutch master issue | Bulgas | Enduro Engine - 2 stroke | 13 | 01-29-2014 10:53 AM |
clutch issue | gasn4christ | Enduro Engine - 2 stroke | 4 | 10-13-2013 03:02 PM |
clutch issue | boostedte37 | General Discussions & Announcements | 2 | 11-09-2009 06:58 PM |