|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Quick question - original top end set-up
A quick question for those who have had the top end off their engine. How was it set up by the factory?
I am currently refreshing the top end on my recently bought EC300 (2010 6 days). The base gaskets were stacked to 1.1mm to match the exhaust port height and the holes in the head steady plates had been elongated to reach the cylinder head. This suggests to me that the motor has had a proper set-up for piston timing and squish. This impression is supported by the opinions of people who have ridden the bike and saythat it performs better than other 300's they have ridden. However, the previous owners confirm that no work has ever been carried out on the engine. For an untouched bike, it seems to have a non-standard set up. Anyone come across this before? |
#2
|
||||
|
||||
My 2010 EC300 Racing had 1.3mm of base gasket stack to time the ports towards top end. It also had 2.6mm+ of squish clearance. What's your squish?
|
#3
|
|||
|
|||
Was going to measure that with the new piston. Probably need to get some thicker solder though.
|
#4
|
||||
|
||||
To save a trip to the store, you can also use a drill to twist multiple thinner solder strands together to wind a consistent rope.
|
#5
|
|||
|
|||
Squish with the new Wosner piston measures 1.8mm. It seems that somebody may have been here before me - strange as the original owner says he never did anything to it.
|
#6
|
||||
|
||||
Every engine is a bit different. Tolerances vary between all parts involved (gaskets included).
|
#7
|
||||
|
||||
1.8 is super dreadful. Just not as bad as some. Machine the head to get it down to 1mm without screwing around with gaskets will retain the same power character but be better in every way. BUT. You MUST carve some out of the chamber or the compression ratio will be way too high even with race gas. Heck probably with methanol.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#8
|
|||
|
|||
ARGHH!
So I had everything ready this afternoon to machine the head. We turned down the hex section of an old plug to serve as a mandrel, screwed it into the head and mounted it up in the chuck. As soon as we turned the lathe on it was clear that something wasn't right as the head was bobbing up and down. A closer inspection revealed the plug hole has been drilled about 1mm off centre. Without a chuck large enough to grip the outside of the head I don't see any easy way of machining the head to reduce the squish. Now to plan B: Remove the barrel and re-install with thinner base gaskets. This will alter the port timing to give more bottom end, which is fine because that is where I am lacking when climbing hills. Obviously I can't go as close on the squish as I would like as this will push the compression too high. I am going to have a look at motopsycho's pics though and see if i can relieve some of the compression by adding some Singh grooves. This won't give me much but it will hopefully give me enough to close the squish a bit. Fortunately I am not using the bike on the road but we have some pretty long, steep, full throttle fire break hills here in Cyprus. I may also have a look at the power-valve flap. Another thread from motopsycho has a description of how he filed back a step on the flap which gave extended top end. To my thinking this will effectively raise the top of the port a fraction which the flap open to compensate for the barrel sitting a fraction lower. |
#9
|
||||
|
||||
That socks. A sparkplug is not much to grip hold of.
So as a check. . .no. . . That's just odd. Surely they would have turned that thread and drilled/tapped the spark hole at the same time. Sorry out of ideas. EBay?
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#10
|
||||
|
||||
On one of my GG 250 heads the spark plug was drilled a degree or 2 off perpendicular which was a nightmare to cut the face for squish. I wonder if they mill the heads at the factory with a 4 jaw chuck or some tool that holds the head from the head stud holes?
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Quick question to all the GG riders out there! | Svippen | Enduro Engine 4 stroke (including EFI & Exhaust) | 3 | 10-10-2016 05:18 PM |
Quick question on reinstalling the front wheel | Koko | Enduro Chassis & Body | 10 | 09-12-2012 06:19 PM |
Quick question about dual map switch position | CDBiker220 | General Discussions & Announcements | 33 | 12-21-2011 09:37 AM |
Quick swingarm/linkage bearing change question | motogroove | Enduro Suspension | 6 | 05-16-2011 12:58 PM |
Quick Gearing Question | Dingo | Enduro Chassis & Body | 6 | 03-23-2009 02:37 AM |