#1431
|
||||
|
||||
I replaced the kickstarter ratchet pinion, starting pinion and spring on my '05 EC300. The cost of the parts was 85 euros including shipping from spain. I put an extra 3mm washer to preload the spring a bit. it was slipping for quite a long time.
What seemed to be a 40 minute job nearly ended in disaster... I overtightened the clutch center nut with the air wrench the last time I had it apart and today I stripped the nut of its thread! thankfully it wasn't the shaft that stripped. and the damn thing is 18X1mm; very difficult to find on a saturday evening... It's ok though, I got a lathe. but no 30 mm hexagon bar, only 27mm. So I filled up the worn nut with the welder and a 29-9 electrode, bored it and rethreaded it. Phew! Last edited by steliost; 12-01-2019 at 03:15 AM. |
#1432
|
||||
|
||||
I put on the studded front tire on my well used Talon wheel. Also replaced the brake disk with a home-made lightly used one. Soon ready for the winter's fun!
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
#1433
|
|||
|
|||
Gas gas fse 450 2004
Clened the chain clenead the entarie engine buyed a piston valves and seals.i picked up the old rebuilded head and waiting to reasamble and hearing her sound for the first time 😁 |
#1434
|
||||
|
||||
Replaced all 3 bearings in the rear Talon wheel and put on a studded Mitas there too. In the front I use a tube this winter, but at the rear I installed a secondhand T-lock I got from a friend. This time I'll keep the summer tires on the OEM wheel set, ready to swap wheels in the spring.
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
#1435
|
|||
|
|||
|
#1436
|
|||
|
|||
Cool. We have cruel weather over here. Its raining since 48 hours and it's bloody cold
|
#1437
|
||||
|
||||
Cleaned mine after a ride on Sunday, cleaned air filter and am giving No-Toil a go. Also gonna give some stinky oils a go, bought so Klotz R50 and Maxima 927.
I run castor oil in my lawn mower and the smell brings back memories of being a kid braaping around the forest |
#1438
|
||||
|
||||
I did nothing to my GasGas today... I'm missing it.
I was stood on the rocks fishing (caught nothing) getting lashed by the waves dreaming of riding my GG... but it's tucked up in the garage back in France while I'm trying to find some winter warmth on the Algarve. |
#1439
|
|||
|
|||
Hello,
Fishing , living in France , off to the Algarve - you don't seem to have a bad life ! |
#1440
|
||||
|
||||
Yes, it's good but I miss my Gasser...
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
DNF today | Pepperami | Enduro Chassis & Body | 6 | 09-18-2013 11:59 AM |
Got my first GG today! | RonMexico | General Discussions & Announcements | 6 | 02-19-2011 12:39 PM |
Went Riding Today and..... | coolum74 | Enduro Engine 4 stroke (including EFI & Exhaust) | 2 | 11-30-2008 01:12 PM |
HELP! I tried to use my gasgas as a jet ski today! | sammyj18 | General Discussions & Announcements | 19 | 11-21-2008 08:01 PM |
SHNF From Today | Boomhauer | Pictures & Videos | 13 | 10-30-2007 04:18 PM |