#101
|
|||
|
|||
Do U just stick them in a vice and bend however much U cut the bars? Heat them up first?
__________________
'14 Beta 300rr '05 GG DE300 '03 GG EC250 '01 XR440 '09 FZ1 |
#102
|
||||
|
||||
thats all i would assume is stick it in a vice and bend it!
__________________
trevor |
#103
|
||||
|
||||
You would think that T.E. would have bark busters preformed for each different handlebar they sell since they only have 3 or 4 different bends but that may not be the case. Mine which I ordered as a set did not come close to matching the handlebars. They are also too long - even though my bars are uncut the barkbusters need about 3/4 inch cut off each one so I can see and operate the buttons on my enduro computer.
|
#104
|
|||
|
|||
So Gasser did U leave any material at the end of the slot, or is it open now? I wonder if U asked, they might send the barkbusters out still in blank form? Cut your own slot?
__________________
'14 Beta 300rr '05 GG DE300 '03 GG EC250 '01 XR440 '09 FZ1 |
#105
|
||||
|
||||
Well mine should ship tomorrow now, I think it took so long because I requested white hand guards and I guess they usually only ship black.
__________________
trevor |
#106
|
|||
|
|||
Quote:
I ordered white hand guards and waited. They sent me black hand guards.
__________________
Eric K '06 GasGas EC300 '01 GasGas XC300 |
#107
|
||||
|
||||
They only sell black I think. Crashed hard last weekend. Bars and guards unscathed. When I installed I cut bars to 30.5". Guards fit perfectly with KTM bend.
__________________
2011 EC300 Six Days 2010 EC300 Nambotin Replica |
#108
|
||||
|
||||
So is it possible to get the TE bars down to 29"?
__________________
Blanco Current ride: 2009 WR450 Previously owned: 12 Gas Gas XC300R, 06 WR450, 06 YZ250, 05 Gas Gas EC250, 05 KTM 450EXC, 02 KX250 w/EG310 kit, 03 YZ250F |
#109
|
||||
|
||||
I went 30.5
remember, the guards don't insert into the end of the bars. The guard straddles and pinches the end. So, whatever you cut is what you get overall.
__________________
2011 EC300 Six Days 2010 EC300 Nambotin Replica |
#110
|
||||
|
||||
I will look when I get home to see if 29 will work.
__________________
2011 EC300 Six Days 2010 EC300 Nambotin Replica |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Twisted Engineering carbon handlebars- Anyone have them? | pscook | Enduro Product Reviews | 22 | 06-22-2013 08:57 PM |
Handguards Enduro Engineering | mikjoh | Enduro Chassis & Body | 1 | 03-31-2012 08:41 PM |
Enduro engineering suspension for gas gas | ScottyR | Enduro Suspension | 16 | 12-16-2010 10:30 AM |
Gas Gas Products by Enduro Engineering | Rod Overstreet | General Discussions & Announcements | 8 | 12-01-2010 04:10 PM |
twisted frame/swingarm saga?? | fullthrottle | Enduro Chassis & Body | 23 | 11-24-2009 07:43 PM |