|
Enduro Electrical & Wiring Lighting, Ignition, Wiring, Plugs, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
2012 EC250E Wiring Issue - No Spark
Hello all, new user here and I have an issue.
I searched the forum and was not able to find anything too fruitful, I bought a 2012 EC250 w/ electric start. When I bought it, it didn't run (had no spark) but after a couple days work I got it going. This time around pulling it out of storage I find I have no spark again. I pulled the wiring harness to do some trouble shooting against the electrical diagram and noticed a lot of funny things: splice after splice after splice, wires leading to nowheres, etc. My question is this, what do I need to have at a minimum connected to get spark? (using kickstarter only) By my logic I'm thinking I need the alternator connected to the CDI and regulator. CDI connected to the Ignition coil. Do iI even need the regulator connected as it just evens out the voltage for the lighting? Lastly, everything must be grounded properly. That said this is what I have connected and still no spark. I checked ignition coil and spark plug and got approx 5kOhm for each. Checking alternator I got 12ish ohm which I believe is reasonable. Not sure how to diagnose CDI. Any help/thoughts would be much appreciated, I will follow up with photos tomorrow. Great forum btw, Thank!! Jeff |
#2
|
|||
|
|||
Skim this topic for ideas. Post #26 covers the ignition requirements.
http://www.gasgasrider.org/forum/showthread.php?t=21215
__________________
2011 EC250E |
#3
|
|||
|
|||
Make sure you disconnect the key switch or at minimum have it turned on. One set of contacts grounds the ignition circuit when the key is off.
The multiple splices and wires going nowhere don't matter unless they are part of the ignition wiring.
__________________
2011 EC250E |
#4
|
|||
|
|||
Thanks for the help Neil,
I dont have the key on this bike, the key switch has been removed. This complicates things a bit, but i think the solution is to jumper two wires somewhere, perhaps wire 38 as per wiring diagram can be grounded? (see wiring diagram 1) Wiring Diagram 1.jpg CDI Wiring Labelled.jpg I confirmed numbers on alternator: - 14.1 Ohm at stator - 95.9 Ohm at pulse Alternator Wiring Readings.jpg and on the iginiton coil: - 5.26 kOhm on plug connector - 5.83 kOhm on ignition wire (to spark plug). Spark Plug Readings.jpg Another question: looking at image of ignition coil, is the tab that connects to CDI wiring supposed to be grounded? (mine is) Ignition Coil Grounding.jpg |
#5
|
|||
|
|||
And just for fun the wiring harness:
Wiring Harness Labelled.jpg |
#6
|
|||
|
|||
The key switch has two functions: OFF= 9 and 20 connected to short out the ignition, ON= 11 and 15 connected to power the estart button.
Do not ground 38 (from the CDI). It is actually 20 (38>21>20) when you follow the path. Your wiring diagram shows 21 also connecting to 22. I believe if you follow this wire, it will go to your kill switch. Do you have a full size image of the wiring diagram? This would help me follow along.
__________________
2011 EC250E |
#7
|
|||
|
|||
Neil,
Just from the bike manual, see GasGas Website: http://www.gasgasmotos.es/en/manuals..._e_en.pdf.html See page 17. Can zoom in pretty good Jeff |
#8
|
||||
|
||||
Im not familiar with gg estart but the key 'on' position may/maynot also open supply to lighting circuit so if theres a short in lighting circuit...no power
__________________
2013 ec200r |
#9
|
|||
|
|||
Check the coil to plug wire connection. The plug wire screws on to the coil. Took me about a month of frustration to find it.
__________________
Dick Carnes "If ya run, you'll only die tired" 2019 EC 300 2018 GP 300 2013 XC 300 (sold) 2006 DE 300 (buddy has it) |
#10
|
|||
|
|||
Ok so I modified the electrical schematic using paint, this is what I have wired in on the bike. everything looks ok to me; one wire off the regulator but it normally goes to the key start. Can anyone see any issues?
Note: the key start is removed, headlights/brakes switches removed, E-Start removed, relay and battery removed (Also, this is not new. Completed by previous owner; it came like this and I have ridden like this so it should work.....) |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
EC250R 2012 high RPM issue | blamir | Enduro Intake/Carburetion - 2 stroke | 83 | 09-04-2014 04:01 PM |
2012 300 e start issue | schlitzy | Enduro Electrical & Wiring | 2 | 08-31-2013 03:07 PM |
2012 ec250e blinkers?? | Novascotiarider | Enduro Electrical & Wiring | 5 | 01-24-2013 01:42 AM |
Rekluse for 2012 EC250E? | robszombie | Enduro Engine - 2 stroke | 15 | 07-20-2012 03:52 PM |
2012 300 issue | bones150 | Enduro Intake/Carburetion - 2 stroke | 7 | 06-22-2012 12:29 AM |