|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Can't put on neutral gear
I made full rebuild on my ec 300 and now the engine is ready ,but i can't put on neutral gear .Another gears work fine ,but won't stay on neutral .When i remove the left engine case i can put on neutral ,but when i assembly the case i can't .I'm confused ,any ideas ?I tried also with oil in tranny ,but its the same.
|
#2
|
|||
|
|||
Shift shaft binding?
Some folks have bent their shift shaft so badly they had to cut it off the splines in order to remove the shaft.
__________________
2011 EC250E |
#3
|
|||
|
|||
Are you sure the shifting parts inside the right side case are assembled correctly? Check the parts for cracked welds.
__________________
2011 EC250E |
#4
|
||||
|
||||
I had a similar problem, but I cannot remember what exactly the problem was. If I remember correctly, there is a spring loaded arm/ roller that is supposed to keep the selector drum in place in neutral. I think my problem had something to do with that arm and its shim or washer being on the wrong side. I did write a post here about it once, but as I said, years ago.
Sent fra min E5603 via Tapatalk
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
#5
|
|||
|
|||
Shift shaft is ok .I'm sure ,that the shifting parts inside the right side case are assembled correctly .Today i put ot neutral once or twice ,but now i can't .
|
#6
|
|||
|
|||
Quote:
|
#7
|
||||
|
||||
This way.. this is the bike in neutral, with the roller sitting up on the ridge between 1st and 2nd on the selector. |
#8
|
|||
|
|||
When i remove right engine case ,i can put the roller on neutral .But when assembly a case I'can't .No logic .
|
#9
|
||||
|
||||
Yes there is always a logic ;-)
Putting on the engine cover will put some pressure om some part because the is a misplaced shim or something similar. Sent fra min E5603 via Tapatalk
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
#10
|
|||
|
|||
Some pics ,i'm sure that the problem is here ,but what is wrong ?
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Off idle bog in gear not in neutral | bluespark | Enduro Intake/Carburetion - 2 stroke | 14 | 04-30-2016 06:01 PM |
Wanted!! Ec200 seat, radiators, switch gear, gear lever | Kendog | "Wanted to Buy" & "Want To Trade" | 2 | 10-12-2014 03:12 PM |
12 ec300r false neutral 5th n 6th gear | scorpa1 | Enduro Engine - 2 stroke | 7 | 04-06-2014 08:22 PM |
Pampera 250 false neutral between 5th and 6th | Schoe000 | Enduro Engine - 2 stroke | 0 | 10-21-2013 03:02 PM |
Gear oil? | nick790 | Enduro Engine - 2 stroke | 7 | 05-18-2009 06:54 AM |