Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Engine - 2 stroke

Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 01-09-2007, 02:04 AM
Gasser370 Gasser370 is offline
Member
 
Join Date: Dec 2006
Posts: 2
Default 00 GasGas EC300 Gear Lever

Any idea what gear lever is compatible with a 00 GG300? I think it is a YZ?

Any ideas will help THANKS


Reply With Quote


  #2  
Old 01-09-2007, 02:24 AM
jeffd jeffd is offline
Gold Level Site Supporter
 
Join Date: Jul 2006
Location: Portland, Oregon, USA
Posts: 417
Default

The only gear lever that is interchangeable with the gasgas shifter is one from a TM (made in italy and not currently imported into the U.S.).

The kickstarter is interchangeable with one off of a yz (late model yz250). The yz part number is listed on the webpage on this site that contains a partial listing of "crossover parts". It can be found at...

http://www.gasgasrider.org/html/parts_crossover.html

jeff
Reply With Quote
  #3  
Old 02-08-2007, 10:12 AM
Loosenut's Avatar
Loosenut Loosenut is offline
Senior Member
 
Join Date: Aug 2006
Posts: 273
Default

The shifter for a 1978 Suzuki RM 125 has the same spline pattern. (I'm assuming I am remembering correctly) They sell cheap steel replacements that can be bent into submission.
Reply With Quote
  #4  
Old 02-08-2007, 10:28 AM
GMP's Avatar
GMP GMP is offline
Senior Member
 
Join Date: Jul 2006
Location: Jefferson Twp., NJ
Posts: 7,601
Thumbs up

No kidding. Very good info and long overdue!
Reply With Quote
  #5  
Old 02-08-2007, 01:04 PM
jeffd jeffd is offline
Gold Level Site Supporter
 
Join Date: Jul 2006
Location: Portland, Oregon, USA
Posts: 417
Default

Loosenut - "you da man!"

Well at first, I thought who in the heck will make an aftermarket shift lever for a bike that old...

Then I looked on the IMS website @ www.imsproducts.com

Flight Line Shift Lever pre-87 RM125
part # 315513

I wonder what the length and shifter tip height is relative to the present gasgas shifter? I have used this before on XRs and they are heavy duty steel - seems to me that as long as the length is good - you could bend it up, down and around as loosenut stated "bent into submission"...

Also, seems to me that if IMS has a shifter that uses the same splines (and they become aware of this) - having them make up one for the gasgas should be a "slam dunk"


jeff
Reply With Quote
  #6  
Old 02-08-2007, 02:45 PM
GMP's Avatar
GMP GMP is offline
Senior Member
 
Join Date: Jul 2006
Location: Jefferson Twp., NJ
Posts: 7,601
Default

As long as its steel, and has the same spline its good. Workable with a torch and cheap arc welder. The shifter fix has been the most frustrating thing about the GGs.
Reply With Quote
  #7  
Old 02-11-2007, 01:27 PM
gasIdaho gasIdaho is offline
Senior Member
 
Join Date: Aug 2006
Location: Driggs, Idaho
Posts: 155
Default

This is info I got from an IMS rep.......

The IMS part no 315513 Flight Line Shift Lever Suzuki RM 125/250 up to 1987

Length from center of shaft hole to center of tip 4 ¾” with an offset away from case approximately 1”

Clamp bolt enters from bottom. Shaft size is the small Suzuki. Suzuki has two shaft O.D.’s. Splines are different than Honda, Yamaha and Kawasaki.

Regards,

Stephen
Reply With Quote
  #8  
Old 02-11-2007, 04:00 PM
GMP's Avatar
GMP GMP is offline
Senior Member
 
Join Date: Jul 2006
Location: Jefferson Twp., NJ
Posts: 7,601
Default

I wonder if they would be willing to make a GG shifter. One of us could even do the prototype and send it to them.
Reply With Quote
  #9  
Old 02-14-2007, 07:32 PM
zero_chances zero_chances is offline
Member
 
Join Date: Feb 2007
Posts: 7
Default

I used to see some on eBay all the time. I just looked and there were none there
Reply With Quote
  #10  
Old 02-19-2007, 09:55 PM
tprnottp tprnottp is offline
Member
 
Join Date: Aug 2006
Location: South of the Mason/Dixon Line
Posts: 51
Default

Quote:
Originally Posted by GMP View Post
I wonder if they would be willing to make a GG shifter. One of us could even do the prototype and send it to them.
GMP:

Whatever happened to Hammerhead Racing making a shifter for us??? Since Hammerhead's products seem to be top shelf, I would buy whatever they produced without hesitation--this includes their brake lever, as well.

As requested, I sent an e-mail to Hammerhead asking for a shifter for my '03 300; they promptly replied, explaining that they were in the process of designing such a shifter, and that it wouldn't be long before it was in production.

I received the above-information a year ago, yet still no shifter advertised on their site.

Are we "back out in the cold," again??? Alternately, I wonder if Les is capable of making a shifter for us. Heck, he's made everything else.

TP
'03 EC 300
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
WTB GasGas EC300 Don180 United Kingdom 1 07-16-2009 03:25 AM
Gear Lever crossover? Leo Enduro Chassis & Body 13 04-17-2009 04:23 AM
Gear lever length ???? pyroman General Discussions & Announcements 3 05-16-2007 07:59 AM
Gear box problem 07 ec300 peterr Enduro Engine - 2 stroke 5 02-26-2007 01:07 AM




All times are GMT -5. The time now is 11:18 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org