|
Enduro Product Announcements Announce new gasgas enduro products here - Vendors Welcome... |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
Scorpion Linkage Skid Plate
This is a new product that should help protect the rear linkage as well as help riders cross over logs and rocks. The photos are of the prototype so the finish is not what the end product will look like. We plan to anodize the side plates red and engrave the Scorpion logo after. We will also be offering a lowering link version that will lower the bike 3/4" at the rear axle. Hope you like it. This product is designed for the 2012.
Last edited by scorpionsteve; 02-17-2012 at 02:31 PM. |
#2
|
||||
|
||||
I could see where a "well placed" rock can do some damage to the shock clevis. Problem solved with your skid plate!
|
#3
|
|||
|
|||
No disrespect to the product, but I have always ridden linkage bikes and a lot of rocks and I have never seen more than a few scratches on the linkage. Not sure if the 2012 linkage is more exposed though.
I know it is always something the orange brigade harp on about when defending their suspension, but has anyone experienced any major rock damage to their linkage?
__________________
2003 txt250 Pro 2013 Ossa 280i |
#4
|
|||
|
|||
Yes the 2012 ( and nambo and cervantes) linkage is quite a bit lower.i will be one of the first customers
|
#5
|
||||
|
||||
swazi_matt no disrespect taken. However it's not just about your linkage taking damage. I have heard with the KTM the rear link has hooked on a rocks stopping the bike dead sending the rider over the bars. The GasGas link does not hang down as much but it does hang down 1 1/2" below the bottom of our 3/16" HD Skid Plate. I think it has the potential to do the same as the KTM (sending a rider over the bars) and this is why we have invested the time and money into developing the product. Time will tell if it was worth it for us or not.
|
#6
|
|||
|
|||
It looks well thought out. Nice product.
|
#7
|
||||
|
||||
Does the guard replace the link arms?
|
#8
|
||||
|
||||
How much Steve?????
__________________
Xr 250 ( first bike) 98 Rmx 2007 Gas gas 300(swapped for trials bike) 2008 280 Raga replica 2012 Gas gas ec 300 E |
#9
|
|||
|
|||
Hi Steve.
I think it's a very good idea. Do you plan to have a distributor in Europe (Portugal) ? Is it also available for the 11' models ?
__________________
Vindicator '11 EC 300R |
#10
|
|||
|
|||
I like the product,, I can see the need.. I have caught my linkage on rocks I have gone over/cased tying to cross them like logs. But then again.. I also ripped the back 1/2 of my airbox off climbing a big ledge on my 97 250 when the shock mud guard caught between the tire and rock face.. I'm also assuming when you said it would lower 3/4 at the rear axle you meant rear of the bike to axle.. as they look rather tall now..
__________________
Steve 16 Beta 350rr 04 KTM 525 sx/exc gone 03 KTM 625 sxc-rehab unit-did its job and now gone 03 GG 250 ec-gone 97 GG 250 ec Gone |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Scorpion skid plate | Stoby | Enduro Product Reviews | 21 | 06-16-2013 08:11 AM |
AXP Skid Plate | gg3 | Enduro Chassis & Body | 2 | 07-18-2011 01:47 AM |
Scorpion Racing Radiator Frames and Skid Plates | Kurdt | Enduro Chassis & Body | 8 | 08-16-2010 05:30 PM |