Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Chassis & Body

Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing.


Reply
 
Thread Tools Display Modes
  #1  
Old 09-06-2017, 11:42 AM
mrfreezer mrfreezer is offline
Member
 
Join Date: Nov 2016
Posts: 67
Default Rear wheel spacers dimensions needed

Hello guys... would anybody be so nice and measure dimensions of rear wheel spacers for ec 250 2008? I want to have them machines because it is difficult to buy those in Slovakia... thanks a lot


Edit: as i have figured out from used bearings and seals all spacers 20mm ID, right spacer 25mm OD, left spacer 25/32 mm OD, spacers between two bearings is 20x42x2mm. So i need to confirm these dimension and add lenghts for all 4 spacers.. thanks a lot



Last edited by mrfreezer; 09-06-2017 at 12:12 PM.
Reply With Quote


  #2  
Old 09-06-2017, 04:46 PM
Neil E. Neil E. is offline
Senior Member
 
Join Date: Mar 2007
Location: Gormley, Ontario, Canada
Posts: 1,418
Default

Here is the dimensions I used to make my own spacers (measured in inches). These dimensions have been rounded off a bit, but you can probably deduce the original metric sizes. To convert divide the inches by .03937 for mm.

If you have trouble I can dig out the original spacers and measure them for metric dimensions. These fit 2011, should work for other years.
Attached Images
File Type: jpg Spacers.jpg (111.4 KB, 56 views)
__________________
2011 EC250E
Reply With Quote
  #3  
Old 09-06-2017, 08:17 PM
(F5)'s Avatar
(F5) (F5) is offline
Gold Level Site Supporter
 
Join Date: Jul 2006
Location: Wellington New Zealand
Posts: 2,063
Default

I bought some aftermarket ones off some French site by searching for the part numbers. Can't remember. But well made and hard anodised.
__________________
'07 EC300 GG
'14 TXT250 GG
'? 496 CPI Cheetah RZ/RGV hybrid
'22 765 Street Triple RS
'21 XTrainer
'69 Stinger T125 Suzuki
'23 TRS 250RR (it's a Trials thing)
Reply With Quote
  #4  
Old 09-07-2017, 07:01 AM
mrfreezer mrfreezer is offline
Member
 
Join Date: Nov 2016
Posts: 67
Default

Neil... thanks a lot.. it helped... I have converted it... can anybody check those other spacera for me?
Attached Images
File Type: jpg 20170907_135756.jpg (122.8 KB, 52 views)
Reply With Quote
  #5  
Old 09-07-2017, 08:37 AM
swazi_matt swazi_matt is offline
Senior Member
 
Join Date: May 2010
Location: From Swaziland, Now Hamilton New Zealand the “look but don’t touch” enduro heaven
Posts: 2,334
Default

doesn't the washer have a step on it?
__________________
2003 txt250 Pro
2013 Ossa 280i
Reply With Quote
  #6  
Old 09-07-2017, 09:07 AM
cbutler's Avatar
cbutler cbutler is online now
Senior Member
 
Join Date: Mar 2009
Location: Hot Springs AR
Posts: 707
Default

Yes it does
__________________

02 EC 200
03 MC 250
88 VT 800
01 TXT 280
Reply With Quote
  #7  
Old 09-07-2017, 10:39 AM
Neil E. Neil E. is offline
Senior Member
 
Join Date: Mar 2007
Location: Gormley, Ontario, Canada
Posts: 1,418
Default

Quote:
Originally Posted by swazi_matt View Post
doesn't the washer have a step on it?
That's a good point. There is a small step that's intended to keep the spacer from falling out when the wheel is removed. I found them to be a nuisance. They push out some of the grease that I fill the lip with so I omitted them.

I'll dig out the originals, but I'm sure I machined the step mostly off for the same reason.
__________________
2011 EC250E
Reply With Quote
  #8  
Old 10-26-2017, 03:21 PM
mrfreezer mrfreezer is offline
Member
 
Join Date: Nov 2016
Posts: 67
Default

guys... can anybody measure the long spacer in the middle of the rear hub? mine is damaged so I can not figure out how long it have to be... the damaged one is 100.5mm long
Reply With Quote
  #9  
Old 10-27-2017, 01:54 AM
swazi_matt swazi_matt is offline
Senior Member
 
Join Date: May 2010
Location: From Swaziland, Now Hamilton New Zealand the “look but don’t touch” enduro heaven
Posts: 2,334
Default

I won't be having my wheel off for a while, but surely the dimension can be measured from the inner wheel bearing race on each side?
__________________
2003 txt250 Pro
2013 Ossa 280i
Reply With Quote
  #10  
Old 10-27-2017, 03:34 AM
mrfreezer mrfreezer is offline
Member
 
Join Date: Nov 2016
Posts: 67
Default

thanks, but I need to have new spacers done before I start to disassemble my wheel
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
wheel spacers kpuc11 Enduro Chassis & Body 9 10-16-2016 05:14 PM
Need inner wheel spacer dimensions GGRider01 Enduro Chassis & Body 0 04-29-2016 12:28 PM
ec 200 wheel spacers gump147 Enduro Chassis & Body 6 03-05-2015 10:35 AM
carb dimensions and advice needed BryanMcc Enduro Intake/Carburetion - 2 stroke 2 09-30-2012 12:59 PM
dimensions needed ltr pv cover mountain thumper General Discussions & Announcements 6 05-04-2010 06:29 PM




All times are GMT -5. The time now is 07:46 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org