|
Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Sticker Kit Peeling
On my original kit, the stickers on the radiator shrouds started to peel off and i could never get it back permanently - ended up just trimming them away from my knees.
I have just received my new cervantes plastic and stickers and see that some of the corners are not stuck down properly and want to make sure that they are glued for good before i use them, so thought i would ask for any tips - superglue, pvc plumbers glue, flour and spit??
__________________
2003 txt250 Pro 2013 Ossa 280i |
#2
|
||||
|
||||
Quote:
That doesn't help, sorry, but I know that super glue doesn't work and neither does the other glue (it'll come to me later, I'm sure). Honestly, the super glue was the worst of the two. You need something that will bond with the plastic as well as work with the current adhesive, and that is a tough nut to crack. Maybe 3M spray adhesive?
__________________
Phil (New bike pending...) |
#3
|
||||
|
||||
Only if you're building a kite.
Clear nail polish works well on the leading edges to prevent further peeling. Last edited by gasgasman; 08-02-2013 at 03:59 PM. |
#4
|
||||
|
||||
I have had good luck with super glue in mine.
__________________
2012 - XC 300 Racing Seattle, WA |
#5
|
||||
|
||||
I have used a heat gun as well with good results.
__________________
Rick 99 EC 200 06 RM 250 AMA D36 375X OTHG 375S ***Thanks for the support : Twin Air /O'Neil Racing / Race 100% / Matrix Concepts / ODI / Mika Metals |
#6
|
||||
|
||||
2010
2010 that also has recently began to have peeling graphics.
Grip glue worked on mine
__________________
2015 KTM 450 XCW 2014 350 XCF Wife's 2009 200 ec. Loving it 2007 Beta Rev 3 270 2007 KTM 200 XC Wife's Public Lands belong to the Public |
#7
|
||||
|
||||
3M Super 77 available at most paint and hardware stores.
__________________
2018 EC 300 |
#8
|
||||
|
||||
have you tried ....
have you tried a very small amount of paint thinner on the glue side ?
When making airplanes....yes airplaines... I saw glue being applied and let dry. then when you were ready to bond the parts togheter a little amount of thinner on the glue re-activate it. I'll try myself have the same issue. |
#9
|
||||
|
||||
If you're putting graphics on new plastic it is essential to clean the plastic to remove the mould release agent and other slippery stuff that may be on the plastic. I've used hot soapy water, rubbing alcohol or contact cleaner with good effect.
When I put down new graphics, invariably the leading edges overs contours don't stick 100%. Where I can I trim with a razor knife to minimize unstuck leading edges. Then, I use Gorilla brand super glue to lay down a seam along the leading edge. Kind of have to finesse a little glue under the leading edge of the graphic, and some in front of it. It's runny glue, so best if the plastic is off the bike so you can move it around to keep the glue where you want it as it sets up - it sets up quick. This keeps dirt from getting under the graphic and then peeling. A bit of work, but it keeps the graphics stuck. |
#10
|
|||
|
|||
I also use a heat gun. keep the heat moving to work out the bubbles and almost melt the stickers to the point that they relax in place. When they cool, they keep the form to the plastic better.
__________________
2006 GasGas EC300 2011 KTM 300XC |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
My little "update," and peeling vinyl question | pscook | Enduro Chassis & Body | 13 | 06-19-2013 10:08 AM |
Extra sticker!!! | modette | General Discussions & Announcements | 2 | 03-03-2013 07:35 AM |
BlackBird Sticker | timlh | Enduro Chassis & Body | 3 | 09-25-2010 05:59 AM |
Sticker | nhrider | General Discussions & Announcements | 0 | 07-10-2008 10:54 AM |
gasgasriders.org sticker | coolum74 | Australia & New Zealand | 1 | 08-20-2007 02:05 AM |