|
Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing. |
|
Thread Tools | Display Modes |
#11
|
||||
|
||||
Cutting and grinding is no big deal. You sure that is all that is required to use the 12 tank?
__________________
Blanco Current ride: 2009 WR450 Previously owned: 12 Gas Gas XC300R, 06 WR450, 06 YZ250, 05 Gas Gas EC250, 05 KTM 450EXC, 02 KX250 w/EG310 kit, 03 YZ250F |
#12
|
||||
|
||||
I don't believe you'll be able to use the new seat, and you will have to fab a mid-seat retainer and rear attangement scheme.
PlusOnePerformance
__________________
Steven Beane #275 PlusOnePerformance - Superior Service the World Over - Dearborn MI AMA District 14 (Michigan) Officer afterhourscycle.com Michigan's Beta and TM Race Headquarters |
#13
|
||||
|
||||
I see....thanks.
__________________
Blanco Current ride: 2009 WR450 Previously owned: 12 Gas Gas XC300R, 06 WR450, 06 YZ250, 05 Gas Gas EC250, 05 KTM 450EXC, 02 KX250 w/EG310 kit, 03 YZ250F |
#14
|
||||
|
||||
Called a heat gun if true...LOL
__________________
Member of AMA, COHVCO, RMAR, Stay the Trail, COTPA Co-Founder of: TrailTaker My site: TrailTaker.com |
#15
|
||||
|
||||
Here you all go:
http://youtu.be/cIMoewC4TMA
__________________
Member of AMA, COHVCO, RMAR, Stay the Trail, COTPA Co-Founder of: TrailTaker My site: TrailTaker.com |
#16
|
||||
|
||||
Modette....twowheels and I installed the flat bar to the seat and then that way it would grab the hook right behind the tank. Makes for the seat to be very solid!!!
__________________
2012 - XC 300 Racing Seattle, WA |
#17
|
||||
|
||||
I'll look at that...
__________________
Member of AMA, COHVCO, RMAR, Stay the Trail, COTPA Co-Founder of: TrailTaker My site: TrailTaker.com |
#18
|
||||
|
||||
Thanks for posting that video.
__________________
Blanco Current ride: 2009 WR450 Previously owned: 12 Gas Gas XC300R, 06 WR450, 06 YZ250, 05 Gas Gas EC250, 05 KTM 450EXC, 02 KX250 w/EG310 kit, 03 YZ250F |
#19
|
||||
|
||||
I looked at the seat yeah you could use the metal cross piece there, but I think with the battery box that will then notch into the hook of the aluminum subframe. Probably because of the added weight on the seat itself with the battery attached to it is why you would want to make sure its down good, the seat is not going anywhere as it stands now. Once I get my box I'll know for sure. I also ordered a new tail/brake light too and I had lost some of the rubber donuts from the radiator that the side plastic snaps into...so I hope it all comes soon.
__________________
Member of AMA, COHVCO, RMAR, Stay the Trail, COTPA Co-Founder of: TrailTaker My site: TrailTaker.com |
#20
|
||||
|
||||
Quote:
The reason I installed that bar to the underside of seat is that on the Factory Replica parts diagram it shows this piece goes there. The bad thing is that the holes do now line up but I went ahead and drilled out my own holes and installed. Why did you have to order a new rear tail light? Here is a good way to prevent those rubber grommets from falling out. Drill small holes just big enough for hand grip tie wire to slip through. Then tie the grommets to your radiators or guards (depending on where you have your grommets). - Problem Solved
__________________
2012 - XC 300 Racing Seattle, WA |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
2012 Poly Subframe | twowheels | Parts | 0 | 09-12-2013 01:52 AM |
2012 snapped subframe | Poncho | General Discussions & Announcements | 21 | 09-14-2012 12:44 PM |
GG Aluminum Frame | ruca | Pictures & Videos | 21 | 05-03-2011 05:29 PM |