Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Intake/Carburetion - 2 stroke

Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 03-11-2012, 07:15 PM
Ed Ventura's Avatar
Ed Ventura Ed Ventura is offline
Gold Level Site Supporter
 
Join Date: Apr 2007
Posts: 131
Default 300 hard starting warm Having some carb issues.

I have a 2011 300 . All electrical is working fine.

I picked this bike up, left it in the basement for 2 months and then went to an enduro. I had a long day.

Bike was pig rich. And Very hard to start warm. Like let it sit 10 minutes then start it.

35 f 20 % humidity
Got home found
36mm ASII
6.5 Slide
NOZH 3rd
40 Pilot
178 main
Air screw No effect.
FLoat 6.5

I lowered the float to 8mm. It seem to help starting but ran still to rich. No Power. A little bit of change with Air Screw

I just installed a # 7 slide that is From My RB modded A.S.I It
Runs Much better. Very Crisp. Will need g2 Throttle cam for tight single track.
BUT"""
Air Screw has no effect. Even with idle screw out. Idles great. If shut it off sometimes it starts good , sometime it takes 20 kicks
Todays Weather 55 F 20 % humidity
Ed


__________________
2011 Sixdays 300

Last edited by Ed Ventura; 03-11-2012 at 08:27 PM.
Reply With Quote


  #2  
Old 03-11-2012, 08:12 PM
Jakobi's Avatar
Jakobi Jakobi is offline
Super Moderator
 
Join Date: Oct 2010
Location: Australia
Posts: 7,994
Default

Quote:
Originally Posted by Ed Ventura View Post
I have a 2011 300 . All electrical is working fine.

I picked this bike up, left it in the basement for 2 months and then went to an enduro. I had a long day.

Bike was pig rich. And Very hard to start warm. Like let it sit 10 minutes then start it.

Got home found
36mm ASII
6.5 Slide
NOZH 3rd
40 Pilot
178 main
Air screw No effect.
FLoat 6.5

I lowered the float to 8mm. It seem to help starting but ran still to rich. No Power. A little bit of change with Air Screw

I just installed a # 7 slide that is From My RB modded A.S.I It
Runs Much better. Very Crisp. Will need g2 Throttle cam for tight single track.
BUT"""
Air Screw has no effect. Even with idle screw out. Idles great. If shut it off sometimes it starts good , sometime it takes 20 kicks

Ed
Do you live in the snow ED?

They all look farrrking phat for a 36mm carb. Bailey ran the NOZH in his 2010 300 at similar temps and elevations to myself (1000ft+ 90F high RH%) in a 38mm ASII - 42 NOZH#1 165. I remember thinking the main was super lean on his but it made great power from all reports and no mechanical issues.

A 36mm will generally require leaner jets as there is a greater vacuum/pull of air and fuel through the carb throat.

The NOZ is a 3 taper needle (same tapers as stock N1Ex) with a half clip leaner adjustment). Third taper generally means fat fuelling towards WOT so a smaller main than if you used a single/twin taper.

Your bike is currently jetted very close to stock.
42 N1EF#2 175
40 NOZH#3 178
1 size leaner on the pilot, 2 sizes leaner on the needle diameter, half a clip richer on the needle, and a size richer on the main.

Last edited by Jakobi; 03-11-2012 at 08:22 PM. Reason: stock jets.. my bad
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Extremely hard starting problems Crankin04 Enduro Engine 4 stroke (including EFI & Exhaust) 27 01-11-2021 02:12 AM
Carb issues - Float bowl? Hicksi Enduro Intake/Carburetion - 2 stroke 7 10-19-2011 11:21 AM
04 EC 300 Hard Starting lordfeyr Enduro Engine - 2 stroke 4 01-25-2010 01:18 PM
2004 450 FSE Hot Starting Issues- MTNBK Enduro Engine 4 stroke (including EFI & Exhaust) 2 06-30-2009 07:19 AM
Hard starting - Timing change? mattmax Enduro Engine - 2 stroke 14 03-03-2007 01:03 PM




All times are GMT -5. The time now is 09:20 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org