Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Intake/Carburetion - 2 stroke

Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc.


Reply
 
Thread Tools Display Modes
  #11  
Old 01-04-2018, 03:31 PM
barossi73's Avatar
barossi73 barossi73 is offline
Gold Level Site Supporter
 
Join Date: Jan 2014
Posts: 551
Default

Fair enough,the NED can feel a little thin in #2 on mine unless its very warm out.A full clip position richer was too much. NEC#3 is that little bit richer and works well for me.Good luck with your jetting.
$20/needle if you need plan B...


__________________
2013 ec200r
Reply With Quote


  #12  
Old 01-04-2018, 10:29 PM
Jakobi's Avatar
Jakobi Jakobi is offline
Super Moderator
 
Join Date: Oct 2010
Location: Australia
Posts: 7,994
Default

I find the NE needles run really good, but as above.. you need to find the right spot.

I'm usually 300-1000M and a cold day here is under 20C. Temps usually well above that and humidity up in the 60+%. I run NEDW#2 in my 250, or N3CW#3.. going leaner on either needle see's the torque run off on small throttle. Going richer adds in some burble and you see some loading up in tech terrain.
Reply With Quote
  #13  
Old 02-04-2018, 03:16 PM
sneaky98gt sneaky98gt is offline
Member
 
Join Date: Dec 2017
Posts: 49
Default

Update.

Spent a few weekends in January doing some tuning / experimenting with the jetting on the bike. Side note: I've gotten really good at changing the needled and/or jets with the carb on the bike. Only takes a few minutes now.

I decided to just tune everything from the beginning. As I expected, it was way rich on the 42 pilot with the AS 1/2 a turn out. I wound up with a 40 pilot at about 1.5 turns out. That's where it idles best, and that's where I get the best throttle response. It has the tiniest, almost imperceptible, bit of 4-stroking just as the throttle is cracked at extremely low loads. Add any kind of load or go past the throttle barely being cracked, and it goes away. Definitely takes a little longer to get warmed up than before, but once it does, it idles fantastically.

With the pilot supplying significantly less fuel now, it was noticeably lean on the needle and main. In the mid-range, it was even less torque than before once warmed up. And at WOT on the pipe, it would ping just a bit after repeated back-to-back runs.

Started by raising the CEK needle one clip (from my initial starting position of 3). Picked up some torque in the mid-range, and the pinging up top went away. Still felt it was a little lean in the mid, so we went ahead and raised the needle another clip all the way to the 5th spot (essentially making it a CCK needle).

Ah, now that hit the spot. Even with the bike nice and hot, it is making great torque off the pipe and through the mid-throttle range. Yet it's not loading up or showing any signs of running too rich when the bike is cooler and/or I'm riding slow techy stuff.

The main that was in it, a 178, felt good, but thought I'd try a 180 just to make sure I didn't need to be richer. Definitely didn't. With the 180, it ran about the same up on the pipe, but was noticeably richer if you went WOT not on the pipe. Put the 178 back in, and all was good.

I rode it in this configuration (178 main, 40 pilot, AS 1.5 out, CEK needle 5th clip) yesterday for about 5 hours up in the mountains at our typical riding park. We rode pretty much the entire variety of terrain we might encounter (very slow techy stuff, fast / flowy singletrack, wide open doubletrack, etc.), and the bike was absolutely brilliant the whole time. LOVED it.

So I might wind up ordering a N3- or NE- needle one day just to play around with it, but I'm loving the bike enough just like it is now that I imagine it'll be a while.
Reply With Quote
  #14  
Old 02-04-2018, 03:57 PM
barossi73's Avatar
barossi73 barossi73 is offline
Gold Level Site Supporter
 
Join Date: Jan 2014
Posts: 551
Default

Cheers for update,enjoy!
__________________
2013 ec200r
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
2011 ec250 jetting ????? dinobody Enduro Intake/Carburetion - 2 stroke 9 04-23-2012 10:50 AM
jetting for ec250 2011 six days taku60 Enduro Intake/Carburetion - 2 stroke 2 02-01-2011 11:01 PM
Once again someone asking for jetting advice husley Enduro Intake/Carburetion - 2 stroke 10 01-16-2011 11:29 PM
06 250 Jetting Advice Brian Enduro Intake/Carburetion - 2 stroke 4 08-28-2010 06:57 PM
Jetting advice Silver Enduro Intake/Carburetion - 2 stroke 11 11-02-2009 04:12 PM




All times are GMT -5. The time now is 11:23 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org