|
Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
7mm Allen tripple pinch bolts.
Two of the tripple Allen head 7mm bolts were partially siezed.
I managed to get them all out (heat, Kroil, old hand impact) But nobody around here has 7mm Allen bolts. Any tips on where to buy some?
__________________
OSSA 2014 Explorer, 1974 OSSA Explorer, Beta 300 Factory 4T, Ducati Multistrada 1000 S, 68 Benelli Dynamo Trail |
#2
|
||||
|
||||
They are an odd ball. I used some longer hex head bolts with steel spacers that fit inside the recess.
|
#3
|
|||
|
|||
__________________
2013 GasGas XC300E 2005 YZ290 1973 Honda CB175 1997 KX60 1983 Yami Tri-Zinger 1984 Suzuki Alt 50 1969 Trail 90 1971 Trail 90 1972 Trail 90 |
#4
|
|||
|
|||
Thanks!
Didn't think of them. Wow- the only one listed I found was high strength - some $5 each!
__________________
OSSA 2014 Explorer, 1974 OSSA Explorer, Beta 300 Factory 4T, Ducati Multistrada 1000 S, 68 Benelli Dynamo Trail |
#5
|
||||
|
||||
I had the same problem..im missing one bolt.. and couldn't find anyone that stocked them..
Sent from my GT-I9300 using Tapatalk |
#6
|
||||
|
||||
The difficult part is finding an allen bolt that is slightly longer so you can make use of the extra threads that the stock bolts are too short to reach.
|
#7
|
|||
|
|||
You could just skip using the middle bolt on each side? On my '13 I just have the middle bolts finger tight with some lock-tite on them to keep them from falling out. It's way to hard to get the torque right with three pinch bolts...
__________________
2013 GasGas XC300E 2005 YZ290 1973 Honda CB175 1997 KX60 1983 Yami Tri-Zinger 1984 Suzuki Alt 50 1969 Trail 90 1971 Trail 90 1972 Trail 90 |
#8
|
|||
|
|||
I had problems finding these as well. I ended up finding a place that had some that were close but the OD of the head was to large. I had a buddy that is a machinist turn the head down. I think he did some extras for me I can look and see if I have any left. I am in Chicago for the week at trade show so when I get back I'll take a look
|
#9
|
||||
|
||||
Maybe European car specialist? I did manage to get some for my old Beta trials bike from the fastener supplies place.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
PV Allen bolt stuck | Shooter | Enduro Engine - 2 stroke | 5 | 04-05-2015 03:23 PM |
WTB front axle & allen cap screw | estwudsracer | Parts | 2 | 06-30-2013 06:33 PM |
Stuck triple clamp pinch bolts | 400_racer | Enduro Chassis & Body | 9 | 08-12-2012 10:32 PM |
Fork Clamp Pinch Bolts - Torque Specs | JP4 | Enduro Suspension | 1 | 03-09-2012 02:03 PM |
Torque Spec's Triple Clamp Pinch Bolts? | ramcclure200 | Enduro Suspension | 6 | 02-20-2008 06:50 AM |