Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > Classified Advertisements > "Wanted to Buy" & "Want To Trade"

"Wanted to Buy" & "Want To Trade" Bikes or Parts


Reply
 
Thread Tools Display Modes
  #1  
Old 02-20-2013, 11:38 AM
richardexclaim richardexclaim is offline
Member
 
Join Date: Jan 2012
Posts: 14
Default Wanted : 45mm Marzocchis

One of mine is cracked at the bottom...

Anyone have a decent set that they want to part with?

Thanks,

Richard
Exclaim Enduro Tours
www.ExclaimTours.com


Reply With Quote


  #2  
Old 02-20-2013, 11:47 AM
jaysktms's Avatar
jaysktms jaysktms is offline
Senior Member
 
Join Date: Oct 2007
Location: Scranton, Pa.
Posts: 124
Default

Let me check upstairs in the garage, tonight.
__________________
13 GasGas 300XC, CLake and now Rekluse
17 Beta 430 RRS, Clake
19 Vertigo 300
03 H-D Nightrain
www.newoodsriders.com
You Can't Out Run Death Forever
But You Can Make the BASTARD Work For It!
Enjoy Life, Have Fun and Play Hard
Reply With Quote
  #3  
Old 02-20-2013, 04:17 PM
Rick's Avatar
Rick Rick is offline
Senior Member
 
Join Date: Aug 2006
Location: Lodi, Ca
Posts: 1,930
Default

Can't you just replace the lug?
__________________
Rick
99 EC 200
06 RM 250
AMA D36
375X
OTHG
375S

***Thanks for the support : Twin Air /O'Neil Racing / Race 100% / Matrix Concepts / ODI / Mika Metals
Reply With Quote
  #4  
Old 02-20-2013, 08:07 PM
GMP's Avatar
GMP GMP is online now
Senior Member
 
Join Date: Jul 2006
Location: Jefferson Twp., NJ
Posts: 7,601
Default

That is a lot more involved than you think. Done incorrectly, you ruin the entire assembly.
Reply With Quote
  #5  
Old 02-20-2013, 08:46 PM
Rick's Avatar
Rick Rick is offline
Senior Member
 
Join Date: Aug 2006
Location: Lodi, Ca
Posts: 1,930
Default

I was under the impression the fork tube is threaded into the lug, sealed by a o ring. Then again I may be wrong.
__________________
Rick
99 EC 200
06 RM 250
AMA D36
375X
OTHG
375S

***Thanks for the support : Twin Air /O'Neil Racing / Race 100% / Matrix Concepts / ODI / Mika Metals
Reply With Quote
  #6  
Old 02-20-2013, 09:08 PM
GMP's Avatar
GMP GMP is online now
Senior Member
 
Join Date: Jul 2006
Location: Jefferson Twp., NJ
Posts: 7,601
Default

Unfortunately I've been through this unsuccessfully, even working with a local machinist. Les warned me it could be a disaster. The lower tube is threaded in the foot, with loctite, and a has setscrew with a point that rolls a couple threads on the tube. That is the tricky part. This damaged thread area has to be precisely machined out with an end mill through the small hole and cleaned with a pick. Then the tube must be held secure, heat, and with some luck its off. Any thread distortion combined with the loctite makes a mess of the foot threads and its impossible to remove after a few turns.

I've never seen a GG Zoke foot separately anyway so you shouldn't have to sweat this option anyway.
Reply With Quote
  #7  
Old 02-20-2013, 11:11 PM
Rick's Avatar
Rick Rick is offline
Senior Member
 
Join Date: Aug 2006
Location: Lodi, Ca
Posts: 1,930
Default

Thanks for the insight.....learn something everyday.....I assumed it was a do-able.
__________________
Rick
99 EC 200
06 RM 250
AMA D36
375X
OTHG
375S

***Thanks for the support : Twin Air /O'Neil Racing / Race 100% / Matrix Concepts / ODI / Mika Metals
Reply With Quote
  #8  
Old 02-21-2013, 08:10 AM
jaysktms's Avatar
jaysktms jaysktms is offline
Senior Member
 
Join Date: Oct 2007
Location: Scranton, Pa.
Posts: 124
Default

Have a set off an 2005 300 EC. These were tuned by LTR, and have the stock 42 in them. Would like to get 150.00 + Shipping. We're are you from so that I can get you a cost.
__________________
13 GasGas 300XC, CLake and now Rekluse
17 Beta 430 RRS, Clake
19 Vertigo 300
03 H-D Nightrain
www.newoodsriders.com
You Can't Out Run Death Forever
But You Can Make the BASTARD Work For It!
Enjoy Life, Have Fun and Play Hard
Reply With Quote
  #9  
Old 02-22-2013, 01:45 AM
Elvis74 Elvis74 is offline
Senior Member
 
Join Date: Jan 2007
Location: Good Old Germany
Posts: 811
Default

I have a pair of 48mm Zokes for sale but shipping would be expensive.
__________________
4 strokes are only good for power generators
Reply With Quote
  #10  
Old 02-22-2013, 09:14 AM
smallpuffydog's Avatar
smallpuffydog smallpuffydog is offline
Bronze Level Site Supporter
 
Join Date: Nov 2010
Location: Durango, CO
Posts: 223
Default

Quote:
Originally Posted by jaysktms View Post
Have a set off an 2005 300 EC. These were tuned by LTR, and have the stock 42 in them. Would like to get 150.00 + Shipping. We're are you from so that I can get you a cost.
Wow! That is a great deal...less than I paid to have mine revalved.
__________________
Believe nothing, no matter where you read it or who has said it, not even if I have said it, unless it agrees with your own reason and your own common sense. [Buddha]
Reply With Quote
Reply




Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Marzocchis on GG300 EC 2011 Mr B Enduro Suspension 2 02-07-2012 10:02 AM




All times are GMT -5. The time now is 03:41 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org