|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
EC300 exhaust
Goodday!
The exhaust of my '02 Gasser EC300 is not in the best shape anymore, Do exhausts of newer EC300 fit? On pics they basically look quite alike/the same. |
#2
|
||||
|
||||
I put two different 2007 pipes on a 2003 GG300 and 2004 GG300. As I recall I needed to shorten the pipe slightly so the muffler would go on all the way and I think I needed to either slightly bend the pipe mounts and or drill a new hole to align with the lower rubber mount. I think one may have also needed a minor dent to provide clearance for the radiator bottom tank. It was relatively easy and I would not hesitate to do it again.
|
#3
|
|||
|
|||
Quote:
Thanks. Edit : What pipe is recommended for a bit more bottom end grunt? |
#4
|
||||
|
||||
I would suggest a FMF Gnarly.
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
#5
|
|||
|
|||
I have a reasonably straight gnarly for an 07 I could sell you for cheap
|
#6
|
|||
|
|||
All I had to do was fit a new lower mounting rubber. One has straight, one has offset.
__________________
2006 EC300 Enduro - Ignitech CDI - 38/NECW#2/165 FMF gnarly, FMF shorty, .50 front 5.7 rear 2016 RM-Z450 |
#7
|
||||
|
||||
Excellent news! Could you have drilled a hole in the lower pipe bracket to align with the original mount?
|
#8
|
|||
|
|||
Smells like too much of a bodge to me
Especially considering the cost of mounts...
__________________
2006 EC300 Enduro - Ignitech CDI - 38/NECW#2/165 FMF gnarly, FMF shorty, .50 front 5.7 rear 2016 RM-Z450 |
#9
|
||||
|
||||
Those mounts look very similar to the original. Was the new one longer or was it offset between the input and output mount locations?
|
#10
|
|||
|
|||
I believe it's pre 07 has straight mount as above. And post 07 has offset mount like such.
__________________
2006 EC300 Enduro - Ignitech CDI - 38/NECW#2/165 FMF gnarly, FMF shorty, .50 front 5.7 rear 2016 RM-Z450 |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
06 ec300 exhaust cat? | motopsycho87 | Enduro Engine - 2 stroke | 2 | 06-24-2013 06:54 PM |
ec300 exhaust pipe | RiverRight | Enduro Engine - 2 stroke | 2 | 08-01-2012 04:09 AM |
? on exhaust for 2010 EC300 | john01 | General Discussions & Announcements | 29 | 11-16-2010 01:33 AM |
EC300 exhaust note | BULTACOBRIS | Enduro Engine - 2 stroke | 5 | 04-27-2009 04:35 PM |