GasGas Riders Club Forum  

Go Back   GasGas Riders Club Forum > Other Bikes... > All Other Bikes...

All Other Bikes... KTM, Husky, VOR, Husaberg & Hondayamazuki...


Reply
 
Thread Tools Display Modes
  #131  
Old 12-09-2018, 08:30 AM
Moto7man Moto7man is offline
Member
 
Join Date: Aug 2011
Location: Murfreesboro,Tennessee
Posts: 2,101
Default

Quote:
Originally Posted by (F5) View Post
Still checking up. Looks good.
Thanks! We will get there.


__________________
2011 GG EC 300E, 1994 CR 250R and 1984 RM 250 E

"If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut."
―Comedian Lewis Black
Reply With Quote


  #132  
Old 01-21-2019, 10:38 AM
Moto7man Moto7man is offline
Member
 
Join Date: Aug 2011
Location: Murfreesboro,Tennessee
Posts: 2,101
Default Swingarm Bearings Install

Made some more progress yesterday.

Bearings installed into the swingarm using a motion pro 20mm bearing driver. Suzuki manual called for bearing numbers to be facing outward and each bearing to be driven 7mm into the swingarm. Very easy install, just make sure that your inner swingarm and bearing are clean and lightly greased. My garage was so darn cold that I didn't need to put the bearings is a freezer.









I packed a heavy amount of BelRay salt water proof grease into the bearings then the seals, then the outer spacer before I installed the bushings, then the inner spacer.







Swingarm bolted up.



__________________
2011 GG EC 300E, 1994 CR 250R and 1984 RM 250 E

"If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut."
―Comedian Lewis Black
Reply With Quote
  #133  
Old 01-21-2019, 10:54 AM
Davehuge's Avatar
Davehuge Davehuge is offline
Senior Member
 
Join Date: May 2017
Location: English but now based in South of France.
Posts: 261
Default

Nice...
Reply With Quote
  #134  
Old 01-21-2019, 10:57 AM
Moto7man Moto7man is offline
Member
 
Join Date: Aug 2011
Location: Murfreesboro,Tennessee
Posts: 2,101
Default Brake Pedal Install

One more picture of the installed swingarm.



Installed brake pedal.





This is where we are so far on this build. The four suspension rod linkage bearings should be here today. I just ordered a set of Goldentyres, a GT216AA 80/100-21 "Razor Blade" for the front and a GT523X "Gummy" for the rear.

__________________
2011 GG EC 300E, 1994 CR 250R and 1984 RM 250 E

"If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut."
―Comedian Lewis Black
Reply With Quote
  #135  
Old 01-21-2019, 10:59 AM
Moto7man Moto7man is offline
Member
 
Join Date: Aug 2011
Location: Murfreesboro,Tennessee
Posts: 2,101
Default

Quote:
Originally Posted by Davehuge View Post
Nice...
Thanks!
__________________
2011 GG EC 300E, 1994 CR 250R and 1984 RM 250 E

"If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut."
―Comedian Lewis Black
Reply With Quote
  #136  
Old 02-07-2019, 01:04 PM
Moto7man Moto7man is offline
Member
 
Join Date: Aug 2011
Location: Murfreesboro,Tennessee
Posts: 2,101
Default New Parts

A lot of new parts are rolling into the garage.

18 and 21 Tubliss.


Goldentyre 216 Razor front tire with tubliss mounted on the new excel rim with Buchanan spokes. This was very easy to install.To the left is the unmounted rear Goldentyre Gummy GT523X, looks very wide doesn't it?



This is the rear gummy mounted up with the tubliss. This tire took a little more time to mount but it wasn't bad.I used armour all to coat the tubliss components and soapy water to seal the system. i bought two of these rear GT523x gummys, the other one is going on the gasser.



This is a VForce 3 Reed from a 1987 250/500 Quadracer, it is supposed to bolt straight into my RM cylinder. V3110-87. Also, this other part is a moose torque reed spacer. This should increase the bottom end and the cylinder has already been ported by Josh at ProCircuit and Josh milled the head to run on pump gas.
__________________
2011 GG EC 300E, 1994 CR 250R and 1984 RM 250 E

"If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut."
―Comedian Lewis Black

Last edited by Moto7man; 02-09-2019 at 12:49 AM.
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
94 CR 250 Ground Up Restoration IMS Wide Ratio Transmission Issue Moto7man All Other Bikes... 146 01-28-2018 06:57 PM
1994 CR 250 Restoration featured on Dirt Bike Magazine Webpage Moto7man Pictures & Videos 8 10-28-2017 10:12 AM
Gas Gas Contact Jt 25 95 Restoration And Help Eyetech General Discussions & Announcements 1 03-18-2016 04:33 PM
2001 XC200 Restoration Project Lincolnlock Enduro Engine - 2 stroke 19 04-22-2014 04:42 PM
My Stomping ground swazi_matt Ride Reports 10 03-02-2011 10:35 AM




All times are GMT -5. The time now is 05:02 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org