Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Intake/Carburetion - 2 stroke

Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 12-01-2017, 11:35 AM
adriano.ro adriano.ro is offline
Senior Member
 
Join Date: Feb 2015
Location: Romania
Posts: 208
Default Richer jetting after squish more?

I don't know if where is the best place to ask this question because is about a KTM .

Is about a KM EXC 250 2011 sxs pipe.

I have set squish to 1.45mm. Jetting 42p N3CJ@4 170main as 1 . Alt 700m temp around 5C.

Bike rips! Wheelie at 90kmh. But I feel a bit to lean on bottom. Can I use 45? Isn't to big? Can I go up on main too? I just want to stay a bit richer.


Reply With Quote


  #2  
Old 12-01-2017, 04:39 PM
Zman's Avatar
Zman Zman is offline
Platinum Level Site Supporter
 
Join Date: Apr 2010
Location: Burbs of Chicago
Posts: 1,818
Default

Honestly you need to try each change one at a time an see if it works better than what you have.
Reply With Quote
  #3  
Old 12-01-2017, 06:14 PM
(F5)'s Avatar
(F5) (F5) is offline
Gold Level Site Supporter
 
Join Date: Jul 2006
Location: Wellington New Zealand
Posts: 2,062
Default

Wind the idle mixture screw in. Is it better or worse?

1.45 is still loose as, but often if you go closer the compression will be way high without taking out of the chamber.
__________________
'07 EC300 GG
'14 TXT250 GG
'? 496 CPI Cheetah RZ/RGV hybrid
'22 765 Street Triple RS
'21 XTrainer
'69 Stinger T125 Suzuki
'23 TRS 250RR (it's a Trials thing)
Reply With Quote
  #4  
Old 12-01-2017, 07:36 PM
adriano.ro adriano.ro is offline
Senior Member
 
Join Date: Feb 2015
Location: Romania
Posts: 208
Default

1.45mm is just a safe zone. I don't have any tunner in country to make the job properly. Squish was 2.1mm
Reply With Quote
  #5  
Old 12-27-2017, 01:17 PM
adriano.ro adriano.ro is offline
Senior Member
 
Join Date: Feb 2015
Location: Romania
Posts: 208
Default

One question: if i use 45 nedw#3 168 (bike run ok,good bottom,good mid and top but too linear for my taste) and I want to use N3CW witch are the adjustment to do ? Bigger main?

Also I feel a bit of hesitation from 1/2 throttle to work on quick open,can be the main jet? Is flat just before power valve is opening after that booooom. In higher gears it feels the moist.

One more: if I use nedw#3 on and I put on necj#4 how the bike will feel?

Tnx guys. Best forum with very nice people.

Last edited by adriano.ro; 12-27-2017 at 02:33 PM.
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
05 ec200 squish, cc's, jetting Zrt1200 Enduro Engine - 2 stroke 14 05-21-2016 04:12 PM
Jetting, S3 heads, Squish band, and other fun stuff! memphis2857 Enduro Engine - 2 stroke 5 07-31-2015 04:15 AM
EC300 - Richer needle = less spooge? mtnmanseth Enduro Intake/Carburetion - 2 stroke 3 05-21-2014 11:22 PM
What needle is half clip richer than N3CJ ? mariogt Enduro Intake/Carburetion - 2 stroke 3 12-09-2012 04:04 PM
2011 GG 300 SD squish, comp, and jetting data Sixdays Enduro Engine - 2 stroke 50 04-02-2012 07:17 PM




All times are GMT -5. The time now is 09:04 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org