Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Intake/Carburetion - 2 stroke

Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 04-16-2018, 11:24 AM
motopsycho87 motopsycho87 is offline
Senior Member
 
Join Date: Jun 2013
Location: Suffolk, UK
Posts: 905
Default Any more info on NExx needles?

On my 2006 300 with AS1 I was running an N3CH, top clip with 42/178 jets and it ran pretty good, but still loaded up slightly at low rpm, which made going from woods to hill climb quite difficult. So I thought I'd try an NECH needle, as they are leaner down low. Now I've run it at top clip 178 main and it's lost a little mid range, so I tried 2nd clip, suddenly rich as hell, so I've dropped to a 168 main, the low and and mid range is there, but at 3/4 throttle it's still a bit rich.

I can't find any information on the actual dimensions of this needle, but I'd like to know where I should be going from here. I'm a bit scared of dropping the main jet any more, are there any NExx needles out there that are just a bit leaner on the final taper area?


__________________
2006 EC300 Enduro - Ignitech CDI - 38/NECW#2/165 FMF gnarly, FMF shorty, .50 front 5.7 rear

2016 RM-Z450
Reply With Quote


  #2  
Old 04-16-2018, 02:17 PM
thumperrider1 thumperrider1 is offline
Senior Member
 
Join Date: Sep 2010
Location: VA
Posts: 499
Default

A pretty good combo on the 300 is an NEDH clip 3, 42 pilot, 170-175 main depending on region.

I"m actually running your settings on my 18 300 and am about to drop in a 180 main. These new bike like fuel.
__________________
2018 XC300
Reply With Quote
  #3  
Old 04-16-2018, 02:35 PM
motopsycho87 motopsycho87 is offline
Senior Member
 
Join Date: Jun 2013
Location: Suffolk, UK
Posts: 905
Default

How's the squish on the new models? Still a prick / tophat situation?
__________________
2006 EC300 Enduro - Ignitech CDI - 38/NECW#2/165 FMF gnarly, FMF shorty, .50 front 5.7 rear

2016 RM-Z450
Reply With Quote
  #4  
Old 04-16-2018, 03:15 PM
thumperrider1 thumperrider1 is offline
Senior Member
 
Join Date: Sep 2010
Location: VA
Posts: 499
Default

Quote:
Originally Posted by motopsycho87 View Post
How's the squish on the new models? Still a prick / tophat situation?
Have not had it apart. I'm sure there is room for improvement. The new motor has plenty of power that's for sure.
__________________
2018 XC300
Reply With Quote
  #5  
Old 04-22-2018, 01:37 PM
motopsycho87 motopsycho87 is offline
Senior Member
 
Join Date: Jun 2013
Location: Suffolk, UK
Posts: 905
Default

So, after a fair bit of jetting I've come to the conclusions of,

(My race bike)
2006 ec300, necj clip 1, 42/162
https://youtu.be/4fCE8rKm_2Q
https://youtu.be/SWtPVZNTCcI
https://youtu.be/_gJx3EHEric


(My sensible commuting bike)
2002 ec300 nedj clip 2 42/165
https://youtu.be/mglniKaEdV4


This is the cleanest my bike has ever run. I started with an NECH needle and 178 main that I'd used with the N3CH needle. The bike ran best with needle in top clip, so I out the NECJ in at number 2, it still ran rich up too, so I went down slowly, 175, 172, 168, 165, 162. I had to stop at that point as I was entering a land no gasgas rider had been to . So I put the 165 back in and dropped the needle, it ran cleaner on mid throttle, but still spluttered at the top, so then I tried 162 and top clip. DAYUM! She revs perfectly clean and has power to boot. Happiest I've been with the bike so far!
__________________
2006 EC300 Enduro - Ignitech CDI - 38/NECW#2/165 FMF gnarly, FMF shorty, .50 front 5.7 rear

2016 RM-Z450

Last edited by motopsycho87; 04-22-2018 at 04:12 PM.
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Needles, needles, needles... Terrence R Enduro Intake/Carburetion - 2 stroke 28 06-26-2015 06:20 PM
jet needles gassergrant Enduro Intake/Carburetion - 2 stroke 7 09-22-2014 12:55 PM
needles? clerky clerk Enduro Engine - 2 stroke 23 10-13-2008 04:06 PM
needles moff747 Enduro Intake/Carburetion - 2 stroke 4 07-09-2008 04:43 PM
Needles skid jackson Enduro Intake/Carburetion - 2 stroke 5 08-17-2007 06:25 PM




All times are GMT -5. The time now is 03:39 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org