|
Other GasGas Bikes/Quads Trials, Pampera, Wild HP, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
GG300 wild alternator
Hi,
How do we remove the alternator nut? Mine is a 30mm socket, and I dont know if it is rigth or left-hand thread. How do we block the crankshaft or flywheel, without damaging it? I will be grateful for your help. |
#2
|
||||
|
||||
If it uses the same crank as the bikes its a normal thread and spins off with an impact tool.
|
#3
|
|||
|
|||
And how do you prevent the crankshaft to spin?
|
#4
|
||||
|
||||
If you have the imact tool it will loosen it w/o it turning. They also make a flywheel holding tool or a piston blocking tool that keeps the motor from turning.
__________________
2004 GasGas DE250 |
#5
|
|||
|
|||
A 1/2" drive air-powered impact wtrench will buzz it right off. You can hold the flywheel with your hand to keep it from spinning. A high-quality 3/8" drive impact will do it too.
If you don't have air tools handy take the spark plug out and feed about about 6" of 3/8" or 5/16" nylon rope onto the cylinder (leave the end hanging out so you don't lose it. It will lock up the engine when the piston comes up against it and shouldn't cause any damage. It would be better to just load it up and pay someone at the local repair shop to buzz the nut off with air tools. Good luck.
__________________
jeff '00 XC250 (mine) LTS front and rear suspension, power valve cover, carb jet kit and rear chain glide, RB Designs head mod, BRP tall triple clamp, backyard foot-peg lowering conversion. '04 EC250 (the kids) (he can do his own mods haha!) |
#6
|
|||
|
|||
It is impossible to hold the alternator flywheel with hands. The nut (30 mm socket) is so tight that it will not come off with the impact wrench, because it make the flywheel to spin together with the nut.
May I have to diassembly the clutch to hold the other crankshaft nut? I never tried to lock the piston through the spark plug hole. |
#7
|
||||
|
||||
This tool is designed to hold the clutch ot your flywheel, $30.
http://www.motionpro.com/motorcycle/partno/08-0008/ Here is the engine lock up tool, $11. http://www.rockymountainatvmc.com/pr...dFamilyId=6067
__________________
2004 GasGas DE250 |
#8
|
|||
|
|||
I will try to lock the piston, since the rotor has a round shape.
thanks for help. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
please help hp wild 450 parts!!!! | gasserwild | Other GasGas Bikes/Quads | 2 | 12-25-2019 10:44 AM |
Raced My 2010 GG300 for the First Time Today | 2whlrcr | Off Road Racer's Corner | 12 | 11-08-2010 09:08 AM |
wild 300 and other 300's | WILDGASGAS300 | Enduro Engine - 2 stroke | 1 | 10-26-2007 11:58 AM |
MC65 has a working alternator | bergerhag | Enduro Electrical & Wiring | 2 | 10-09-2007 05:34 AM |
Wild 300 Hp | PA300HPWILD | Enduro Electrical & Wiring | 0 | 10-09-2006 06:59 AM |