Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > Other Bikes... > Other GasGas Bikes/Quads

Other GasGas Bikes/Quads Trials, Pampera, Wild HP, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 03-04-2017, 11:40 AM
Blambo Blambo is offline
Member
 
Join Date: Mar 2016
Posts: 17
Angry Front wheel not central

My front wheel runs WAY too close to the RH fork (left as seen from the front).
I've taken it all apart and checked it against the parts diagram and logically and it's all 'correct'.
So, what has changed ?
It can only be that I changed the wheel bearings...
If the RH bearing wasn't seated (sitting proud) that would HELP, i.e. push the wheel towards the centre.

Has anyone seen this before ?

What about the DISTANCIADOR RUEDA DEL.17.2MM INT / FRONT WHEEL SPACER BEP250218019 ? part 11 on page 3 of the parts book.
(this is inside the wheel, between the bearings).
I remember when I changed the bearings that this is non-symetrical, but there didn't seem any obvious reason to put it in one way or the other.
I guess I must have got this the wrong way round.
Shame I'll trash at least one of the new bearings getting it out...
Sigh,
Mike
Reply With Quote
  #2  
Old 03-04-2017, 12:44 PM
gasgasman's Avatar
gasgasman gasgasman is offline
Super Moderator
 
Join Date: Jul 2006
Location: Pearland Texas
Posts: 4,594
Default

Is the rotor centered with the caliper?
Reply With Quote
  #3  
Old 03-04-2017, 11:15 PM
Jakobi's Avatar
Jakobi Jakobi is offline
Super Moderator
 
Join Date: Oct 2010
Location: Australia
Posts: 7,994
Default

Picture? Year model? Bearing part numbers that you replaced? Did you confirm them the same size/make?
Reply With Quote
  #4  
Old 03-05-2017, 05:31 AM
Blambo Blambo is offline
Member
 
Join Date: Mar 2016
Posts: 17
Default details of art numbers (interesting!|)

Hi,

It's a mk2 Pampera 250 (2002).
I used AllBalls bearings, labelled for Pampera their part # 25-1135
Everything looks right, the brake works ok, but the wheel is just too close to one fork leg.

Part numbers are interesting...
The bearing numbers were 6003, same as I used in the rear.

But the parts manual has 2 different numbers for the front wheel bearings.
R=BEP250218007 L=BIE500118054
The supplied bearings were 6003 same as the rear bearings, both labelled as 6003, BIE500118054 in the parts book.
So, should I have had one 6003 and another different one ???
I have e-mailed AllBalls to see what they say...

Mike
Reply With Quote
  #5  
Old 03-05-2017, 09:11 AM
Jim Cook's Avatar
Jim Cook Jim Cook is offline
Platinum Level Site Supporter
 
Join Date: Sep 2006
Location: Smackover, Arkansas (AR)
Posts: 687
Thumbs up

Quote:
Originally Posted by Blambo View Post
Hi,

It's a mk2 Pampera 250 (2002).
I used AllBalls bearings, labelled for Pampera their part # 25-1135
Everything looks right, the brake works ok, but the wheel is just too close to one fork leg.

Part numbers are interesting...
The bearing numbers were 6003, same as I used in the rear.

But the parts manual has 2 different numbers for the front wheel bearings.
R=BEP250218007 L=BIE500118054
The supplied bearings were 6003 same as the rear bearings, both labelled as 6003, BIE500118054 in the parts book.
So, should I have had one 6003 and another different one ???
I have e-mailed AllBalls to see what they say...

Mike
Did you look at the numbers on the bearings that you took out of the wheel? Do you still have them in order to check them?
__________________
Jim Cook
Smackover Racing
Team LAGNAF
'11 Gas Gas EC250 (primary ride)
'06 Gas Gas DE300
2004 Gas Gas TXT300 Pro
'94 Husaberg FE350
'86 Yamaha IT200
'86 Honda TRL200 Reflex
'04 KTM 525EXC (soon to be dual sported)
Several others, including project bikes, Deb's bike, and a fleet of grandkids' bikes

Let's go riding!
http://www.jebruns.com/Wudi19/wudi19.html
http://www.ahrma.org/schedules-results/cross-country/
Reply With Quote
  #6  
Old 03-05-2017, 09:39 AM
gasgasman's Avatar
gasgasman gasgasman is offline
Super Moderator
 
Join Date: Jul 2006
Location: Pearland Texas
Posts: 4,594
Default

If the rotor is centered, you will have to adjust your spokes to shift the rim over.
Reply With Quote
  #7  
Old 03-07-2017, 07:19 AM
hadfield4wd hadfield4wd is offline
Senior Member
 
Join Date: Oct 2015
Location: Roanoke, VA
Posts: 852
Default

Spacers on the right sides? Was it centered before you did wheel bearing? Whenever I see something like this my first question is "what changed?"
__________________
Matt

1999 GG EC 250 Six Days
1999 Cagiva Gran Canyon
2001 Aprilia Falco
2001 Triumph Speed Triple for my 20 year old
2000 GG XC250 for my 20 year old
2003 Honda Rancher 350 for the wife
Reply With Quote
  #8  
Old 03-07-2017, 12:31 PM
swazi_matt swazi_matt is offline
Senior Member
 
Join Date: May 2010
Location: From Swaziland, Now Hamilton New Zealand the “look but don’t touch” enduro heaven
Posts: 2,334
Default

Are the wheel spacers the same size?
Does the brake disk look like it is in the right place relative to the forks?

A picture or two will probably help
__________________
2003 txt250 Pro
2013 Ossa 280i
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Cant get my front wheel off mwinschel Enduro Chassis & Body 7 03-05-2016 01:13 AM
FOR SALE, 250XC forks, NEW fender, front wheel, front wheel bearings iamyvr Parts 5 07-27-2014 08:18 AM
Front wheel ? Silver Enduro Chassis & Body 2 04-20-2009 05:33 PM
Will anything other than a GG front wheel fit a GG? cal_tony Enduro Chassis & Body 7 11-08-2008 09:21 AM




All times are GMT -5. The time now is 09:26 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org