Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Intake/Carburetion - 2 stroke

Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 02-17-2014, 08:21 PM
MikeS MikeS is offline
Member
 
Join Date: May 2012
Posts: 11
Default 08 EC 300 Stalling when hot

Hi,

My 300 has been stalling lately when hot and riding slower, tight single track mostly. Usually first couple hours it runs great, and has ran perfectly all day riding faster single track. Only when tight 1st, 2nd gear steep stuff does it die out on me. I have done the following:

JD Jet Kit
Clean air filter
adjusted idle
new spark plug
clean gas always, mixed 50:1

Should I adjust air screw?

The puzzling part is how well it runs at the start and riding slightly faster stuff. Stalls mostly on downhills...

Thoughts much appreciated. pic attached just for fun...
Attached Images
File Type: jpg 20140117_131511 copy.jpg (129.7 KB, 30 views)


Reply With Quote


  #2  
Old 02-18-2014, 07:18 PM
jimjim jimjim is offline
Senior Member
 
Join Date: Jul 2011
Posts: 189
Default

Have you checked your powervalve?
Reply With Quote
  #3  
Old 02-19-2014, 08:53 AM
phoenix's Avatar
phoenix phoenix is offline
Senior Member
 
Join Date: Aug 2012
Location: Oklahoma City, OK
Posts: 279
Default

Mine does the same thing (wanting to stall going down hills), but I haven't gotten around to working on the problem. I was told by some fellow 2 strokers to check my float height, so I'm going to start there. I'll check the powervalve too now.
__________________
2009 Husqvarna TXC 450
2013 Husaberg TE 300
2014 Gas Gas XC 200

Reply With Quote
  #4  
Old 02-19-2014, 09:12 AM
desertgasser300 desertgasser300 is offline
Banned
 
Join Date: Feb 2011
Location: Hot A@% desert AZ.
Posts: 1,872
Default

Quote:
Originally Posted by phoenix View Post
Mine does the same thing (wanting to stall going down hills), but I haven't gotten around to working on the problem. I was told by some fellow 2 strokers to check my float height, so I'm going to start there. I'll check the powervalve too now.
My thoughts exactly to check float height.

Sent from my QMV7A using Tapatalk
Reply With Quote
  #5  
Old 02-21-2014, 12:52 AM
MikeS MikeS is offline
Member
 
Join Date: May 2012
Posts: 11
Default

Thanks guys, power valve is fine as I did a full rebuild 40 hours ago. Plus it runs fine for the first few hours which makes me think it's not one of those two issues... Anything else you can think of? I thought maybe it's just the idle screw slowly turning itself out so I have tried just adjusting that just in case. Not sure what else to do. Cheers,

Mike.
Reply With Quote
  #6  
Old 02-21-2014, 04:30 AM
Jakobi's Avatar
Jakobi Jakobi is offline
Super Moderator
 
Join Date: Oct 2010
Location: Australia
Posts: 7,994
Default

The angle the carb sits in the bike leans it forward towards the engine. Have a look in my lectron thread and you'll see with a clear bowl that the angle that the fuel sits. Add in the factor for the whole bike leaning forwards (ie downhill) and a few bumps, and its easy to have the engine load up enough to stall out. You can improve it by dropping the fuel level some, but you don't want to get to a point where there isn't enough fuel in the bowl for extended WOT situations.

At the end of the ride often the airfilter is also a bit dirtier and creates a slight richer condition which also contributes.
Reply With Quote
  #7  
Old 02-23-2014, 12:17 AM
MikeS MikeS is offline
Member
 
Join Date: May 2012
Posts: 11
Default

Great points thanks for the reply.

Mike
Reply With Quote
Reply




Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Stalling down hills? nick790 Enduro Intake/Carburetion - 2 stroke 3 09-05-2009 02:28 AM
Another 450 with stalling problems mrsticky Enduro Engine 4 stroke (including EFI & Exhaust) 3 06-11-2009 11:37 AM
Bike stalling out smnl4l Enduro Engine 4 stroke (including EFI & Exhaust) 6 11-19-2008 11:06 PM
Question: Stalling? Tinks United Kingdom 2 02-25-2008 08:11 AM
Stalling on the downhills gasIdaho Enduro Intake/Carburetion - 2 stroke 2 04-16-2007 12:16 AM




All times are GMT -5. The time now is 01:12 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org