Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Engine - 2 stroke

Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 05-12-2007, 08:46 PM
j@y j@y is offline
Member
 
Join Date: May 2007
Posts: 1
Default what ratio to premix at?

hi guys,
i just purchased a 2001 ec200. it has full fmf exhaust and i believe a boyesen rad valve from what i can see. i run 32:1 in my rm125 but am not sure if this is what i should run in the ec. any help would be greatly appreciated


Reply With Quote


  #2  
Old 05-12-2007, 08:59 PM
gasgasman's Avatar
gasgasman gasgasman is offline
Super Moderator
 
Join Date: Jul 2006
Location: Pearland Texas
Posts: 4,589
Default

That's what I run in mine.
Reply With Quote
  #3  
Old 05-12-2007, 09:28 PM
Brian VT Brian VT is offline
Senior Member
 
Join Date: Jul 2006
Location: Vermont, USA
Posts: 827
Default

I run my EC300 on Amsoil Dominator at 40:1. My buddy runs his EXC300 on Amsoil Sabre at 100:1.
If your motor's in good shape and jetted properly you should be fine with the recommendations on the can.
Reply With Quote
  #4  
Old 05-13-2007, 05:56 AM
Bearman's Avatar
Bearman Bearman is offline
Senior Member
 
Join Date: May 2007
Location: Victoria, Australia
Posts: 199
Default

i run my 03 200 at 50:1. im the third owner and myself and the last owner (who is a great mate of mine) have both run this bike at that premix using Motul 800. its fully synthetic and neither of us have had any problems
Reply With Quote
  #5  
Old 05-13-2007, 03:35 PM
iancp5's Avatar
iancp5 iancp5 is offline
Senior Member
 
Join Date: Aug 2006
Location: U.K.
Posts: 829
Default

I do what the manual says 50:1. I use quality oil & I get very little wear. Modern, quality oils are very good and cling to the metal so once you have enough adding more to the fuel doesn't improve wear it just clogs things up faster. I think if you want to protect your engine better just keep ontop of the air filter situation. It's muck getting in that wears things out usually not lack of oil.
Reply With Quote
  #6  
Old 05-13-2007, 05:31 PM
eff's Avatar
eff eff is offline
Silver Level Site Supporter
 
Join Date: Jul 2006
Location: RI
Posts: 1,758
Default

I run 50:1 too, Mobil Racing 2T Synth.
Reply With Quote
  #7  
Old 05-13-2007, 11:17 PM
skid jackson skid jackson is offline
Senior Member
 
Join Date: Jul 2006
Location: NH, USA
Posts: 1,057
Default

same here ......
Reply With Quote
  #8  
Old 05-14-2007, 09:46 AM
widebear's Avatar
widebear widebear is offline
Banned
 
Join Date: Nov 2006
Location: Kamloops B.C.
Posts: 723
Default

A few years back I bought two cases of Amsoil , back then it was all 100-1. When I ran out , year before last I went to a dealer and bought a gallon jug of Amsoil dominator. Without realizing that Amsoil had changed its product line up,( read not looking at instructions) I ran the dominator at 100-1, even though its meant for 50-1. Last year When i did the top end on my mc250, still had'nt clued in, everything looked fantastic, no problems whatsoever. It was only this spring did i realize my mistake. I can't say enough good things about this stuff. It works!
Reply With Quote
  #9  
Old 05-14-2007, 02:33 PM
JoshP's Avatar
JoshP JoshP is offline
Senior Member
 
Join Date: Aug 2006
Location: Stockholm, NJ
Posts: 118
Default

I've been running Motul 50:1 with the high grade gas in my Gassers and Kawa's.
Reply With Quote
  #10  
Old 05-16-2007, 10:19 PM
GregM GregM is offline
Member
 
Join Date: Jul 2006
Posts: 45
Default

Assuming the bike is jetted properly, is there a brand of oil that keeps visible exhaust smoke to a minimum or none at all?

Greg
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
FAQ: Premix Calculations MattR Enduro Intake/Carburetion - 2 stroke 20 02-11-2019 02:30 PM
premix W8TSON Enduro Engine - 2 stroke 31 08-11-2009 10:52 AM
gear ratio breakdown?? Cruiser General Discussions & Announcements 3 04-06-2009 09:53 PM
Pre-Mix ratio gasIdaho Enduro Intake/Carburetion - 2 stroke 8 03-21-2007 12:17 PM
premix ratio for 300 two-stroke gateman Enduro Engine - 2 stroke 3 09-27-2006 07:29 PM




All times are GMT -5. The time now is 07:49 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org