Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > Classified Advertisements > Parts

Parts New/Used Components and All Bike Part Outs


Reply
 
Thread Tools Display Modes
  #1  
Old 06-14-2016, 03:07 AM
64Opaka 64Opaka is offline
Member
 
Join Date: Apr 2012
Posts: 12
Default need:Starter Clutch Bendix 2013 EC300

Do you happen to have a Bendix starter clutch for a 2013 EC300? If so I am in the market. I tried to use a Honda (chinese) one but the stock gearing was no good. Please advise. Thank you


Reply With Quote


  #2  
Old 06-14-2016, 03:40 AM
pigpen966 pigpen966 is offline
Senior Member
 
Join Date: Dec 2012
Location: Ohio
Posts: 204
Default

http://www.gasgasrider.org/forum/showthread.php?t=19737
__________________
Dick Carnes
"If ya run, you'll only die tired"
2019 EC 300
2018 GP 300
2013 XC 300 (sold)
2006 DE 300 (buddy has it)
Reply With Quote
  #3  
Old 06-14-2016, 06:37 AM
Wimpy525 Wimpy525 is offline
Senior Member
 
Join Date: Oct 2011
Location: Catawissa Pa
Posts: 394
Default

I just put a SMU5009 in my 13 with a little modification as listed in the post mentioned above. Also Matto Cycle is looking to modify the SMU5009 so it will be a direct replacement with no modifications needed. Not sure how far along he is as we just spoke about it last week.
Reply With Quote
  #4  
Old 06-23-2016, 06:25 PM
64Opaka 64Opaka is offline
Member
 
Join Date: Apr 2012
Posts: 12
Default What are we doing wrong?

We just installed a new 5009 Bendix with the mods you so very kindly provided. However we can't seem to get it to turn the flywheel. There seems to be ample clearence and the starter works great but the bendix is not engaging the flywheel. Do you happen to have any suggestions? Everything else seems to work just fine. I look forward to any tips you may have.
Reply With Quote
  #5  
Old 06-23-2016, 06:59 PM
Wimpy525 Wimpy525 is offline
Senior Member
 
Join Date: Oct 2011
Location: Catawissa Pa
Posts: 394
Default

There are three different gaskets for the stator cover. Depending on where the fly wheel is position on the crank. Right now I have a thicker gasket installed as the bendix was binding on the ring gear I also had to shim out the top of the starter to get everything lined up. You may want to try pulling the fly wheel and reinstalling and see what happens then.
Reply With Quote
  #6  
Old 06-27-2016, 02:19 PM
64Opaka 64Opaka is offline
Member
 
Join Date: Apr 2012
Posts: 12
Default Different Gaskets

I tried different gasket thicknesses, but something my riding partner reminded me of was that when we tried to run the bendix without the flywheel cover on with the starter motor we could not get the bendix drive to drop down into position to drive the flywheel. Is this caused by the sping on the bend being too tight? Should I stretch it out a bit. Any suggestions would be much appreciated.
Thank you!
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Starter bendix Ned600rr Parts 2 05-04-2016 08:45 PM
2005 450 Starter Clutch Blues meanmarv Enduro Engine 4 stroke (including EFI & Exhaust) 0 07-07-2013 01:18 AM
2013 EC300 Clutch play skidmarx Enduro Engine - 2 stroke 0 06-30-2013 08:56 PM
Starter clutch / gear problem iancp5 Enduro Engine 4 stroke (including EFI & Exhaust) 12 01-28-2011 03:45 PM
2002 ec400fse starter clutch jason r Enduro Engine 4 stroke (including EFI & Exhaust) 6 09-09-2009 05:47 PM




All times are GMT -5. The time now is 05:19 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org